User manual ISOUND TIMEDOCK

[. . . ] Attention should be drawn to the environmental aspects of battery disposal 14. ) 15. ) 16. ) 17. ) 18. ) 19. ) 2 IMPORTANT NOTES Avoid installing this unit in places exposed to direct sunlight or close to heat radiating appliances such as electric heaters, on top of other stereo equipment that radiates too much heat, places lacking ventilation or dusty areas, places subject to constant vibration and/or humid or moist areas. No naked flame sources, such as lighted candles, should be placed on the apparatus. No objects filled with liquids, such as vases, shall be placed on the apparatus. Do not attempt to clean this unit with chemical solvents as this might damage the finish. [. . . ] To remove the tab, pull it in the direction of the arrow in the illustration as shown. When the operation of the remote control becomes intermittent or unsatisfactory, replace the original battery with a new 3-volt lithium battery. 2. ) Place one 3V CR2025 battery in the battery holder, observing the positive (+) direction. If the battery is placed incorrectly the remote control will not work. Notes: Use a well-known brand of cell battery for longest life and best performance. When the remote operation becomes intermittent, replace the battery. 9 OPERATING INSTRUCTIONS Make sure the AC power cord from this unit is properly connected to a 110V 60Hz household AC power outlet. Make sure that the minimum distance around the whole unit for sufficient ventilation is 10cm. SETTING THE CLOCK When the system is connected to the AC outlet for the first time and "12:00" will keep flashing on the display. 2. ) Press HOUR or MINUTE to adjust the hour digit and minute digit respectively. 3. ) Press the TIME button again to confirm and the clock begin to run. The PM indicator will light up when it is afternoon. SLEEP FUNCTION This system includes a programmable sleep timer that allows you to set the unit to turn off between the 5 minutes to 2 hours 1. ) Sleep function can only be operated under OFF and AUTO mode. 3. ) Press the SLEEP button and the iPod will turn on and start playing and the default sleep time will show on the display. 4. ) The sleep time is default at 2 hours, press the SLEEP button to change the sleep time. The sleep time will change in following order every time you press the SLEEP button: 2:00 > 1:30 > 1:00 > :30 > :20 > :10 > :05 > -:-- minutes 10 5. ) Release the SLEEP button to confirm setting. 6. ) When the SLEEP time is reached the unit will turn off itself under OFF, or AUTO mode. 7. ) You can shut the unit off manually during the Sleep time by pressing the SNOOZE button at any time or press the SLEEP button until -:-- appear on the display. ALARM FUNCTION 1. ) Alarm Function will only activate on AUTO mode. Then press HOUR or MINUTE button to adjust the hour digit and minute digit respectively. 3. ) Press the ALARM button again to confirm and the alarm time is set. Select MUSIC means the alarm will activate by the following sequence: i) If iPod is docked, the alarm is defaulted to Wake by iPod. 7. ) When the alarm time is reached, the alarm is activated by the selected source. 8. ) Press ALARM to stop the alarm and the alarm will activate again in the next day at the same time until you cancel the alarm function. 9. ) To cancel the alarm function, slide the FUNCTION switch to OFF mode to switch the alarm off. 10. ) If no action takes place in an hour after the alarm is activated, the alarm will 11 turn off itself. 11. )If SNOOZE button is pressed during the alarm is activated, the alarm is set to re-activate in 9 minutes. [. . . ] 5) Press the VOLUME + / VOLUME ­ button on top panel or remote control to adjust the VOLUME level of this unit as desired. Then the unit will become a 2. 1 system and the bass would be able to sound from the external active subwoofer. Note: The connection cables and active subwoofer are not included. RESETTING If the system does not have any respond, you may have experienced a severe electric shock (ESD) or a power surge that triggered the internal computer to shut down automatically. If this occurs, simply disconnect the main power and connect the main power again after one minute. [. . . ]