User manual JENSEN CD-477 DATASHEET

[. . . ] Protect the Disc Mechanism Avoid inserting any foreign objects into the disc slot. Misuse may cause malfunction or permanent damage due to the precise mechanism of this unit. THIS UNIT USES A VISIBLE/ INVISIBLE LASER BEAM WHICH COULD CAUSE HAZARDOUS RADIATION IF EXPOSED DIRECTLY. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OR PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. [. . . ] button again to resume playback. Repeat Play (CD) Touch the RPT button during disc play to repeat play the current track. Touch the RPT button during disc play to repeat play the current file. Touch RPT again to stop repeat play. Repeat Play (MP3/WMA) 13 VR209TP Display Modes (MP3 Discs) Touch the INFO button to toggle between MP3 files/directories view and large screen format, where the artist, song title and album is displayed. NOTE: Only six tracks are displayed at one time. Touch the up/down arrows to the right of the list to access additional tracks. Shuffle Play · · · · · Touch the SHUF button on the touch screen during disc play to play all tracks/files in random, shuffled order. During MP3/WMA/USB playback, touch SHUF a second time to play all songs in the current folder. Touch the INTRO button to play an introduction of each file, beginning with the next track/file. Touch INTRO again to stop intro play and play the current track/file in full. Intro Play Direct Track/File Access 1. Touch the button to make the keypad appear on the screen. 2. Enter the track/file number using the keypad in the center of the screen to directly select a track/file. button on the keypad to backspace and cancel wrong number input. NOTE: Touch the 3. Touch the ok button to play the entered track/file number. NOTE: To exit the screen without making an entry, touch the button. 14 VR209TP USB OPERATION 8 1 2 3 4 5 6 13 7 10 11 12 9 NOTE: The USB button is operative only when a USB device is connected. Removing a USB Device Change to another mode and then remove the USB device from the USB connector. Accessing USB Mode from Another Playback Mode Touch the USB button on the right side of the touch screen to access USB mode. Touch and hold a preset location on the screen until the channel is stored and appears in the preset list. Switching to SIRIUS Mode Press the AUDIO button (4) to access Audio mode (if needed). Touch the SAT button on the touch screen to access the Sirius Radio. Recalling a Stored Channel The stored channels can be accessed directly by touching the corresponding preset location on the touch screen. Touch the up/down arrows to the right of the list to access the next group of stored presets. SIRIUS Tuning Modes Channel Tuning Mode Touch TUNE +/- to go to next/prev channel. Preset Tuning Mode · · · · · · Touch and hold the PRESET button to enter Preset Tuning Mode. Use the up/down arrows on the side of the screen to display additional choices. Category Mode Activating Sirius Satellite Radio Before you listen to Sirius Radio, you must subscribe to the service using your radio's identification number. To display the Radio ID, touch the TUNE + or TUNE - button to access channel "000". The screen displays "Radio ID" followed by a 12 figure ID number. 17 VR209TP Direct Channel Access 1. Use the on-screen number pad to re-enter the new 4-digit code, and then press the ok button. If the new code is correctly entered twice, "Code Saved" appears on the screen and the radio returns to SIRIUS mode. "Channel Locked" appears and the audio is muted for this channel. When a user returns to this channel, the user code must be entered to hear the audio. [. . . ] This type of noise can be easily detected because it will vary in intensity of pitch with the speed of the engine. Usually, the ignition noise can be suppressed considerably by using a radio suppression type high voltage ignition wire and suppressor resistor in the ignition system. (Most vehicles employ this wire and resistor, but it may be necessary to check them for correct operation. ) Another method of suppression is the use of additional noise suppressors. These can be obtained from most CB/A radio or electronic supply shops. Interference Radio reception in a moving environment (automobile) is very different from reception in a stationary (home) environment. [. . . ]