User manual JENSEN JIMS-190

[. . . ] DOCKING DIGITAL MUSIC SYSTEM FOR iPod® OWNER'S MANUAL JiMS-190 (iPod® Not Included) PLEASE READ THIS OPERATING MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN THIS BOOKLET FOR FUTURE REFERENCE TABLE OF CONTENTS DEAR JENSEN® CUSTOMER IMPORTANT SAFETY INSTRUCTIONS COMPLIANCE WITH FCC REGULATIONS PRODUCT FEATURES INSTALLATION LOCATION OF CONTROLS RADIO OPERATIONS iPod® DOCKING AUXILIARY INPUT CLOCK AND CALENDAR SETTINGS ALARM OPERATIONS CARE AND MAINTENANCE TROUBLESHOOTING GUIDE SPECIFICATIONS SERVICE 2 2 3 4 4 5-6 7 8 9 10 11 12 13 14 14 "Made for iPod" means that an electronic accessory has been designed to connect specifically to iPod and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this device or its compliance with safety and regulatory standards. and other countries. DEAR JENSEN CUSTOMER Selecting fine audio equipment such as the unit you've just purchased is only the start of your musical enjoyment. Now it's time to consider how you can maximize the fun and excitement your equipment offers. [. . . ] To activate the remote control, remove the insulation tab inserted in the battery compartment. AC-DC Adaptor Connection An AC-DC Adaptor with the output DC10V 1400mA (included) is required for operating the main unit. 1. Firmly insert the DC plug of the adaptor (included) into the DC Jack on the back of the unit 2. Plug the adaptor's AC plug into your household AC power outlet (120VAC/60Hz). NOTE: This unit is not magnetically shielded and may cause color distortion on the screen of some TVs or video monitors. To avoid this, you may need to move the unit further away from the TV or monitor if unnatural color shifts or image distortion occurs. 4 LOCATION OF CONTROLS Main Unit Top view Bottom view 21 1 22 2 12 7 9 6 11 5 10 4 38 Front view Rear view 16 15 13 14 15 20 19 18 17 1. iPod® Dock 2. iPod® Docking Connector 3. POWER On/Off Button To turn the unit on or off 4. VOLUME +/- Buttons Adjust the volume level up or down 5. SNOOZE/LIGHT Button Activate the snooze function; Turn the LCD backlight on or off 6. TUN +/- /iPod Buttons Tune the radio channel frequency up or down; iPod® Skip/Search Forward/Backward Buttons for Backward, for Forward. 7. CH +/- Buttons Select the preset radio stations 8. ALARM On/Off Button Switch the alarm on or off 9. SLEEP Button Select the time duration of the sleep timer 10. MODE Button Enter the setting mode 11. MEM/iPod Button Save the radio preset stations; save settings; iPod® PLAY/PAUSE 12. FUNCTION Button Select AM/FM Radio, iPod® mode and AUX (auxiliary input) mode 13. LCD Display 14. Remote Infra-red Sensor 15. Pair of Speakers 16. AUX in Jack An Audio Cable with a 3. 5mm stereo plug for the connection of external audio device 17. Cord Retracting Wheel For extending or retracting the auxiliary cord 18. DC Jack To connect to external DC power supply 19. Headphone Jack 20. FM Antenna Terminal 21. Battery Compartment It is to contain two 'AAA' batteries for clock back-up 22. RESET Button For resetting the unit 5 LOCATION OF CONTROLS Remote Control 1 6 7 RECORD 2 3 8 9 10 11 13 12 CH 4 5 12 1. Infra-red Transmitter 2. POWER On/Off Button 3. VOL +/- Button 4. FUNCTION Button 5. ALARM On/Off Button 6. SNOOZE/LIGHT Button 7. TUN Up/Down Buttons for Down, for Up 8. CH +/- Buttons 9. MEM Button 10. MODE Button 11. SLEEP Button 12. iPod® Skip/Search Forward/Backward Buttons for Backward, for Forward. 13. iPod® PLAY/PAUSE 14. Battery Compartment 14 6 RADIO OPERATIONS FM Antenna Connect the detachable FM Antenna Wire to the FM Antenna Terminal as instructed in the section "INSTALLATION". 2. Press the FUNCTION button repeatedly until "AM" or "FM" mode is reached. 3. In FM radio mode, if necessary, press the MODE button to select STEREO (ST) or MONO FM reception. 4. To manually tune the radio station, repeatedly press the TUN Up/Down Buttons. 5. To automatically search the next or previous station with the strongest signal, press and hold the TUN Up/Down Buttons until the frequency readout on the display begins to scan and then release the button. The tuner will stop scanning until the strongest signal station is searched. You should turn off the iPod manually or remove it from the unit for better reception. 7 iPod ® DOCKING If the docking port will not be used for an extended period of time, it is recommended to cover the docking port by using the "Dock Cover" insert (included). 1. Use the iPod adaptor included in your iPod and insert it into the docking area. Your iPod can now be inserted into the docking port by placing the connector on the bottom of the iPod onto the connector in the docking bay. Note: Please be careful when seating the iPod into the docking to avoid damaging the 30-pin connector on iPod or docking system. 3. Press the FUNCTION button repeatedly until the indicator "iPod" shows on the display. 5. Press the VOL +/- button on the docking system to adjust your desired volume level NOTE:The volume level cannot be adjusted by the volume control of your iPod ® after being docked. NOTE: The iPod will only charge in iPod, AUX, or power "OFF" modes. 7. To remove the iPod® from the unit, press and hold the PLAY/PAUSE button for three seconds to switch off the device and then gently remove it from the docking connector. [. . . ] - Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors. Resetting the Unit If the unit is subject to a power surge or electric shock, it is possible that the internal micro-controller may lock up and the unit will not respond to any commands from the top panel controls or remote control. 1. In this event, unplug and then reconnect the AC power plug into the wall outlet. 2. Use a straightened paper clip, toothpick or similar objects to press the RESET button located on the bottom of the main unit (see the below figure). [. . . ]