User manual JENSEN SMPV-8GBK DATASHEET

[. . . ] WARNING: · · TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES. 2 JHD1120 INSTALLATION This unit is designed for installation in vehicle cabs with an existing 1-DIN radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. Always check the kit application before purchasing to make sure the kit works with your vehicle. [. . . ] The removal keys are depicted in "Removing 53 the Unit" on page 3. Screw Stud Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Check that there will be sufficient space behind the dashboard for the radio chassis. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation. After completing the wiring connections, turn the unit on to confirm operation (vehicle accessory switch must be on). If the unit does not operate, recheck all wiring until the 9. Removing the Unit To remove the radio after installation, remove the plastic end caps, insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Sleeve Removal Key 2. Reconnect Battery When wiring is complete, reconnect the battery negative terminal. 3. Removal Key 4. BAT OFF (Off / On): When ON, radio will automatically turn off when vehicle battery voltage is below 10. 8 VDC. RESET ALL <ENTER>: Press the INFO/ENTER button (16) to return the EEPROM to factory default set up values. The following items can be adjusted: · · · · Equalizer Press the EQ/LOUD button (11) to choose one of the following pre-defined bass and treble curves: USER > FLAT > ROCK > CLAS(SICAL) > POP. Loudness Press and hold the EQ/LOUD button (11) to toggle loudness on/off. When listening to music at low volumes, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Auxiliary Input To access an auxiliary device: 1. Connect the portable audio player to the AUX IN on the front panel (17). Press MODE again to cancel "Auxiliary" mode and go to the next mode. Liquid Crystal Display (LCD) The current frequency and activated functions are shown on the LCD panel (21). NOTE: LCD panels may take longer to respond when subjected to cold temperatures for an extended period of time. In addition, the visibility of the characters on the LCD may decrease slightly. The LCD display will return to normal when the temperature increases to a normal range. 6 JHD1120 Setting the Clock To set the clock to display the current time, turn the vehicle ignition on and turn the radio on. Enter the system menu and adjust the clock by selecting the "CLK" menu item. · · · · Press the INFO/ENTER button (16) to view the clock set screen. Press the TUNE/SEEK |<< / >>| (18, 19) buttons to adjust the selected digit. [. . . ] Dropping it can damage circuit boards and cases, and can cause the product to work improperly. Wipe the product with a dampened cloth occasionally to keep it looking new. Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the product. High temperature can shorten the life of electronic devices, damage batteries, and distort or melt plastic parts. TROUBLESHOOTING Symptom No power Cause The vehicle's accessory switch is not on Solution If the power supply is properly connected to the vehicle's accessory terminal, switch the ignition key to "ACC" or "Run" Replace the fuse Adjust volume to audible level Check wiring connections Press the RESET button The fuse is blown No sound Volume is too low or system is muted Wiring is not properly connected The operation keys do not work Cannot tune to radio station, auto-seek does not work The built-in microcomputer is not operating properly due to noise The antenna cable is not connected The signals are too weak Ignition The most common source of noise in reception is the ignition system. [. . . ]