User manual JENSEN VOYAGER VCCT130

[. . . ] Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers. Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle. NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player. 2 JCD3006 INSTALLATION Before You Begin 1. Disconnect Battery Before you begin, always disconnect the battery negative terminal. [. . . ] Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard. Place the radio in front of the dashboard opening so the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections are secure and insulated with crimp connectors or electrical tape to ensure proper operation. secure part of the dashboard Screw Stud Hex Nut (5mm) either above or below the radio using the screw and plain Spring Washer washer provided. CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of the radio or improper operation due to vibration. Re-attach the front panel to the chassis and test radio operation by referring to the operating instructions for the unit. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove downwards and reattach. ) Insert the removal keys straight back until they click, and then pull the radio out. If removal keys are inserted at an angle, they will not lock properly to release the unit. Dashboard 2. Removal Key Trim Plate Installation Push the trim plate against the chassis until it is fitted. You must do this before you install the control panel, otherwise it can't be attached. DIN Rear Mount (Method B) This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some vehicles to mount the radio to the dashboard. Please consult with your local mobile stereo shop for assistance on this type of installation. Press the up >>| (21) button to adjust the hours or the down |<< button (20) to adjust the minutes. (You can also use the U and D buttons on the remote control to set the hour and minutes. ) JCD3006 Reset After releasing the control panel, use a pencil or any non-metallic object to press and hold the RESET button for five seconds to reset the main unit. The reset button should be activated for the following reasons: 1 6 RE SE T 5 20 21 12 13 14 15 16 17 10 9 8 11 18 · · · initial installation of the unit when all wiring is completed function buttons do not operate error symbol on the display Control Panel Release (REL) Press the REL button (3) to release the control panel. Power On/Off ( ) Press the button (1) to turn the unit ON or OFF. 1 VOL S 4 NOTE: If after pressing the RESET button the unit still does not function normally, use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. 6 VOL Volume Control To increase the volume, rotate the volume control knob (6) clockwise. To decrease the volume, rotate the volume control knob counter clockwise. When the volume is adjusted, the volume level is shown on the display panel as a number ranging from 00 (lowest) to 100 (highest). 20 19 9 D TR. UP 10 BND SCN MOD 5 7 LOC AMS PEQ 8 23 MO PAU 11 MUT SCN Press the volume control button (4) on the control panel (or the S button on the remote control) to access the Audio Menu. You can navigate through the Audio Menu items by pressing the volume control button repeatedly, or by pressing the up >>| (21) or down |<< (20) buttons. Once the desired menu item appears on the display, adjust that option by turning the volume control knob within 5 seconds. The unit will automatically exit the Audio Menu after five seconds of inactivity. Volume Level Use the volume control knob to adjust the Volume level from "00" (lowest) to "100" (highest). Bass Level Use the volume control knob to adjust the Bass level range from "-10" to "+10". [. . . ] Play/Pause Disc Playback (1/PAU) Press the 1/PAU button (12) to suspend disc play. Intro Scan (2/INT) Press the 2/INT button (13) on the control panel (or the 2/SCN button on the remote control) to play the first 10 seconds of each track sequentially. Press 2/INT again to stop Intro Scan and resume normal play at the current track. Repeat Play (3/RPT) Press the 3/RPT button (14) during disc play to repeat play the current track. [. . . ]