User manual JENSEN VOYAGER VOM-58

[. . . ] Do not use CDs with labels or stickers attached or that have sticky residue from removed stickers. Do not expose discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a vehicle parked in direct sunlight where there can be a considerable rise in temperature inside the vehicle. NOTE: A disc may become scratched (although not enough to make it unusable) depending on how you handle it and other conditions in the usage environment. These scratches are not an indication of a problem with the player. 2 JCDWIN INSTALLATION Before You Begin 1. Disconnect Battery Before you begin, always disconnect the battery negative terminal. [. . . ] Consult with your nearest dealer if installation requires the drilling of holes or other modifications to your vehicle. Install the unit where it does not interfere with driving and cannot injure passengers if there is a sudden or emergency stop. If the installation angle exceeds 30º from horizontal, the unit might not give optimum performance. This unit is not waterproof and is intended for interior mounting applications only. Exterior mounting of the unit requires use of an ASA approved marine housing. Avoid installing the unit where it will be subject to high temperatures from direct sunlight, hot air, or from a heater, or where it would be subject to excessive dust, dirt or vibration. Be sure to remove the control panel before installing the unit. 9. Mounting the Unit This unit can be property installed with a conventional DIN front mount. Slide the mounting sleeve off of the chasDashboard sis if it has not already been removed. If it Bend Tabs is locked into position, use the removal 182 keys (supplied) to disengage it. The removal keys are depicted in "Removing 53 the Unit" on page 3. Screw Stud Check the dashboard opening size by sliding the mounting sleeve into it. "BAL L=R" represents an equal balance between the right and left speakers. Fader Use the button to adjust the Fader between the rear and front speakers from "10R" (full rear) to "10F" (full front). "FAD R=F" represents an equal balance between the front and rear speakers. BND SCN MOD 8 7 9 12 13 MO P AU MUT SCN DISP RPT Mute Press the MUTE button (8) on the control panel (or the MUT button on the remote control) to mute the audio output. Press MUTE again to restore the audio output to the previous level. Loudness Control (LOUD) When listening to music at low volume levels, this feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press the BAND/ LOUD button (21) again to turn the LOUD function off. 1 2 3 4 SHUF 5 6 Mode Press the MODE button (5) on the control panel (or the MOD button on the remote control) to select a different mode of operation, as indicated on the display panel. Available modes include Radio, CD, and AUX In (optional Auxiliary Input). Connect the external signal to the "Aux In" jack (20) located on the front of the control panel. If you have a device connected to the rear auiliary input, the front auxiliary device will override the rear one. Press the MODE button to select Aux In mode. Audible Beep To turn on/off the audible beep heard when a function is selected, press and hold the AUDIO control button (4) on the control panel (or the S button on the remote control) to access the Beep option. Within five seconds, turn the AUDIO control (4) to choose between the following modes: "BEEP ALL", "BEEP OFF", or "BEEP 2ND". Choose "BEEP 2ND" to hear a beep only when secondary functions are activated (for example, functions accessed when you press and hold a button). 5 JCDWIN Display Selector (DISP) This unit can display either the clock time or radio frequency/CD player functions. [. . . ] Each band stores up to six preset stations. Tuning Auto Seek Tuning Press the TUNE up (19) or TUNE down button (18) on the control panel (or U and D on the remote control) for less than three seconds to move to the next station automatically. Manual Tuning Press the TUNE up (19) or TUNE down button (18) for more than three seconds to enter manual tuning mode. Press the TUNE up or TUNE down button to change the radio frequency number up or down one step. Scan Press the SCAN button (22) on the control panel (or SCN on the remote control) to automatically search for stations. Each available station will flash on the display for a few seconds before the next is searched. [. . . ]