User manual JETWAY 917GBAR3A
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual JETWAY 917GBAR3A. We hope that this JETWAY 917GBAR3A user guide will be useful to you.
Manual abstract: user guide JETWAY 917GBAR3A
Detailed instructions for use are in the User's Guide.
[. . . ] 917PBAG/917PBA 917GBAG/917GBA USER'S MANUAL
M/B For LGA 775 Pentium 4 Processor
NO. G03-917GBA Rev:3. 0 Release date: March 2005
Trademark:
* Specifications and Information contained in this documentation are furnished for information use only, and are subject to change at any time without notice, and should not be construed as a commitment by manufacturer.
TABLE OF CONTENT
USER'S NOTICE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii MANUAL REVISION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii COOLING SOLUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Without this connector might cause system unstable because the power supply can not provide sufficient current for system.
Pin 1
(3) (4) (5) (6) (7)
USB Port connector: USB1 USB Port connector: UL1 (USB) The connectors are 4-pin connector that connect USB devices to the system board. LAN Port connector: LAN(only for 917PBAG/917GBAG) This connector is standard RJ45 connector for Network connector. PS/2 Mouse & PS/2 Keyboard Connector: KB (PS2 KB/MOUSE) The connectors for PS/2 keyboard and PS/2 Mouse. Parallel Port Connector (25-pin female): PARALLEL Parallel Port connector is a 25-pin D-Subminiature Receptacle connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information.
(8)
(9)
VGA Connector (15-pin D-Sub) Connector: VGA (for 917GBAG/917GBA only) VGA is the 15-pin D-Subminiature female connector for display monitor
Audio Line-In, Lin-Out, MIC, Surrback, Surround, GEN/LEF Connector : J1 This Connector are 6 phone Jack for LINE-OUT, LINE-IN, MIC, Surrback, Surround, GEN/LEF Audio output to speaker Line-out : (GREEN) Audio input to sound chip Line-in : (BLUE) Microphone Connector MIC : (PINK) Audio output to speaker-Rear speaker out Surrback : (ORANGE) Surround : (BLACKNESS) Audio output to speaker-Center/Subwoofer speaker out Audio output to speaker-Side speaker out GEN/LEF: (GRAY)
(10) Serial Port COM1/COM2(COM2 only for 917PBAG/917PBA): COM1/COM2 is the 9-pin D-Subminiature mail connector. Please refer to Chapter 3 "INTEGRATED PERIPHERALS SETUP" section for more detail information.
22
Line-IN PS/2 Mouse PRINT
Line-OUT Surrback LAN
PS/2 COM1 Keyboard
VGA GEN/LFE
USB2
USB MIC-IN SURROUND
(11) Floppy drive Connector (34-pin block): FDD This connector supports the provided floppy drive ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to the floppy drives.
FDD
Pin 1
Floppy Drive Connector
(12) Primary IDE Connector (40-pin block): IDE1 (Support ATA 100) This connector supports the provided IDE hard disk ribbon cable. After connecting the single plug end to motherboard, connect the two plugs at other end to your hard disk(s). If you install two hard disks, you must configure the second drive to Slave mode by setting its jumpers accordingly. Please refer to the documentation of your hard disk for the jumper settings. (13) Secondary IDE Connector (40-pin block): IDE2 (Support ATA 133) This connector connects to the next set of Master and Slave hard disks. You may also configure two hard disks to be both Masters using one ribbon cable on the primary IDE connector and another ribbon cable on the secondary IDE connector.
IDE1
IDE2
Pin 1
Pin 1
23
· ·
Two hard disks can be connected to each connector. The first HDD is referred to as the "Master" and the second HDD is referred to as the "Slave". For performance issues, we strongly suggest you don't install a CD-ROM or DVD-ROM drive on the same IDE channel as a hard disk. Otherwise, the system performance on this channel may drop.
(14) Serial-ATA Port connector: SATA1/SATA2/SATA3/SATA4 This connector support the provided Serial ATA IDE hard disk cable to connecting the motherboard and serial ATA hard disk. Serial-ATA RAID Port connector: SATA5/SATA6 This port support RAID0, RAID1, RAID0+1 functions.
Pin 1
SATA4 SATA3 SATA2 SATA1
Pin 1
SATA6 SATA5
Serial-ATA RAID Port
Serial-ATA Port Connector
2-6-2 Headers
(1) Line-Out, MIC Header (9-pin): AUDIO This header connect to Front Panel Line-out, MIC connector with cable.
AUD-G ND AUD-VC C
AUDIO
Pin 1
2
10 9
Line-Out, MIC Headers
(2)
USB Port Headers (9-pin) : USB3, USB4 The header is used for connecting the additional USB port plug. By attaching an option USB cable, your can be provided with two additional USB plugs affixed to the back panel.
24
AUD-MIC AUD-MIC-BIAS AUD-FPO -R UT HP- O N AUD- FPO -L UT
+DATA G ND O C
-DATA
Pin 1
Pin 1
+DATA G ND
-DATA
USB Port Headers
(3)
(4)
IDE Activity LED: IDE LED This connector connects to the hard disk activity indicator light on the case.
Reset switch lead: RESET This 2-pin connector connects to the case-mounted reset switch for rebooting your computer without having to turn off your power switch. This is a preferred method of rebooting in order to prolong the lift of the system's power supply. Power LED: PWR-LED The Power LED is light on while the system power is on. Speaker connector: SPEAK This 4-pin connector connects to the case-mounted speaker. Power switch: PWR BTN This 2-pin connector connects to the case-mounted power switch to power ON/OFF the system.
PWR LED PWRBTN
PWRBTN PWRLED
(5)
(6) (7)
VCC5
PWRLED
Pin 1
JW FP SPEAK
Pin 1
SPKR NC VCC5
Pin 1
GND
HDLED
System Case Connections
(8)
FAN Power Headers: SYSFAN1, SYSFAN2 (3-pin), CPUFAN (4-pin) These connectors support cooling fans of 350mA (4. 2 Watts) or less, depending on the fan manufacturer, the wire and plug may be different. Connect the fan's plug to the board taking into consideration the polarity of connector.
25
RESET
GND RSTSW NC
VCC5 HDDLE
GND
+D ATA G ND
-DATA
VC C
VC C
-DATA
VC C
VC C
USB3
+DATA G ND O C
USB4
CPUFAN SYSFAN1
1 1 4
3
SYSFAN2
3 1
FAN Power Headers
(9)
IR infrared module Headers (5-pin) : IR This connector supports the optional wireless transmitting and receiving infrared module. [. . . ] Supervisor password: User password:
43
Chapter 4
DRIVER & FREE PROGRAM INSTALLATION
Check your package and there is A MAGIC INSTALL CD included. This CD consists of all DRIVERS you need and some free application programs and utility programs. In addition, this CD also include an auto detect software which can tell you which hardware is installed, and which DRIVERS needed so that your system can function properly. We call this auto detect software MAGIC INSTALL.
MAGIC INSTALL Supports WINDOWS 2000/XP
Insert CD into your CD-ROM drive and the MAGIC INSTALL Menu should appear as below. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE JETWAY 917GBAR3A
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual JETWAY 917GBAR3A will begin.