User manual JONSERED FT 5

[. . . ] pREPARATION · While working, always wear substantial footwear and long trousers. Thoroughly inspect the area were the equipment is to be used and remove all objects which can be thrown by the machine. WARNING: Petrol is highly flammable: - store fuel in containers specifically designed for this purpose; - refuel outdoors only and do not smokewhile refueling; - add fuel before starting the engine. [. . . ] Insert stake support between engine bracket halves with stake spring down. NOTE: It may be necessary to loosen nut "A" · Bolt stake support to engine brackets with bolts, lock washers and nuts. If a higher handle height is desired, loosen the four nuts securing handle panel to engine brackets. Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs. Use clean 30 or 10W-30 grade oil and store in approved, clean covered containers. Starting up when the engine is cold Once the engine starts, slide the choke to the "run" position. Starting when the engine is warm Start the engine with a quick pull of the recoil starter. All variations of speed and depth of cultivation are dependent on the position of the supporting wheels and arrester bar. The arrester bar must always be lower than the level of the wheels during cultivation. The function of the arrester bar is to slow down the movement of the cultivator so that the blades dig into the soil. Set the arrester bar higher if you want the cultivator to till less deeply. The braking effect of the arrester bar can also be adjusted by reversing the pointed end of the bar to point either forwards or backwards. Lifting the handlebars slightly will increase the cultivator's speed of propulsion, which means that the blades will not dig as deeply into the soil. Pressing the handlebars down has the effect of reducing the speed of the machine, and making the blades work deeper. When cultivating hard or stony ground, it is advisable to proceed slowly. When cultivating hard ground or peat, it is advisable to cultivate 2-3 times in succession, working gradually deeper over the same area of ground. Always cultivate at right angles to the previously worked direction (cross cultivation). Stones and roots may become jammed between the blades and the chain case. [. . . ] Clean the cooling system as well as the outside of the rest of the engine. When ordering spare parts, remember to state the product number of your machine. No gasoline in fuel tank Fill tank with gasoline Throttle control not set properly Place throttle control in "FAST" position Choked improperly, flooded engine Move choke control to "RUN" position or place throttle control in "FAST" position and pull starter several times to clear out gas Clogged fuel tank Remove and clean Dirty air filter Remove and clean or replace Spark plug dirty or improper gap Clean, adjust gap or replace Loose wiring Check the wiring and spark plug Water in gasoline or old fuel Drain fuel tank and carburetor, use fresh fuel and replace spark plug Improper carburetor adjustment Make necessary adjustments Engine misses or lacks power Engine overloaded Set depth stake and wheels for shallower tilling Clogged fuel tank Remove and clean Partially plugged air cleaner Remove and clean or replace Improper carburetor adjustment Make necessary adjustments Dirty air screen Clean air screen Spark plug dirty, improper gap or wrong type Replace spark plug and adjust gap Poor compression Major engine overhaul Oil in gasoline Drain and refill gas tank and carburetor Dirty air screen Clean air screen Low oil level or dirty oil Add or change oil Dirty engine Clean cylinder fins, air screen, and muffler area Partially plugged muffler Remove and clean muffler Improper carburetor adjustment Adjust carburetor Ground too wet Wait for more favorable soil conditions Le starter du moteur n'est pas utilisé correctement, le moteur est noyé Placez le starter à la position de marche "RUN" ou placez l'accélérateur en position rapide "FAST" et tirez le démarreur plusieurs fois pour éliminer le gaz Réservoir d'essence obstrué Démontez-le et nettoyez-le Filtre à air sale Enlevez-le et nettoyez-le ou remplacez-le La bougie est encrassée ou la distance est incorrecte Nettoyez, réglez la distance ou remplacez Câble mal serré Vérifiez le câble et la bougie Il y a de l'eau dans l'essence ou l'essence est trop vieille Vidangez le réservoir d'essence et le carburateur, utilisez de l'essence neuve et remplacez la bougie. [. . . ]