User manual JUNO JKI3333

[. . . ] " It is dangerous to alter the specifications or modify this appliance in any way. " Care must be taken to ensure that the appliance does not stand on the electrical supply cable. " The domestic refrigerators and freezers are designed to be used specifically for the storage of edible foodstuffs only. " Manufacturers' storage recommendations should be strictly adhered to. [. . . ] For building into kitchen units follow the special "Building-in" instructions given. The appliance's door have been locked in position for transport by means of pins on both sides. According to the door opening direction, remove relevant pins at the top and at the bottom. 50 mm min. cm 200 2 Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. For operation with different voltages, a suitably sized auto-transformer must be used. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. The Manufacturer declines all responsibility if the above safety precautions are not observed. This appliance complies with EEC directive number 87/308 of 2/6/87 relative to radio interference suppression. D022 For safety reasons, minimum ventilation must be as shown in Fig. Attention: keep ventilation openings clear of obstruction. D567 Fig. 2 A Push appliance into housing until stop strip (A) touches the kitchen unit. Fig. Directives: - 73/23 EEC of 19. 2. 73 (Low Voltage Directive) and subsequent modifications; - 89/336 EEC of 3. 5. 89 (Electromagnetic Compatibility Directive) and subsequent modifications. D265 Cleaning the interior Before using the appliance for the first time, wash the interior and all internal accessories with lukewarm water and some neutral soap so as to remove the typical smell of a brand-new product, then dry thoroughly. Do not use detergents or abrasive powders, as these will damage the finish. If after having carried out the operation described in section 2 there is still some space left between the appliance and the kitchen unit, fit the trimming provided together with the appliance on the stop strip (A). 11 Fig. 8 Open the door and push the appliance against the side of kitchen furniture opposite to that of appliance hinges. D Fasten the appliance with 4 screws provided in the kit inC cluded with the apD130 pliance. 5 8mm PR34 Open both the appliance door and that of the kitchen unit to approx. Hold the doors of the appliance and the unit together and mark the holes. Fig. 9 Press in the joint covers between the appliance and the kitchen furniture. D132 Fig. Replace the little plates over the runners and screw in the screws provided (3. 5x16 mm). For the alignment of the kitchen unit door, PR35 if necessary, use the clearance size of the slotted holes. At the end of the procedure, check that the doors of the appliance and the kitchen unit open properly. Apply covers (B) on joint cover lugs and into hinge holes. Inner door reversal Fig. 7 1 PR140 H 20m m D094 Position the runners (H) at the top and bottom of the inside of the kitchen unit as shown in Fig. After preparing the holes, screw the runners to the kitchen unit door using 3. 5x16 mm screws. Using a screwdriver release bracket (1) by pressing on the i n t e rn a l s p r i n g (Fig. [. . . ] 12 PR151 when defrosting is completed, dry the interior thoroughly and refit the plug; keep the scraper for future use; turn the thermostat knob back to the required setting or replace the plug in the power socket. After two or three hours, reload the previously removed food into the compartment. D037 Important: A temperature rise of the frozen food packs, during defrosting, may shorten their safe storage life. 14 MAINTENANCE Unplug the appliance before carrying out any maintenance operation. Warning This appliance contains hydrocarbons in its cooling unit; maintenance and recharging must therefore only be carried out by authorized technicians. Interior light The light bulb inside the refrigerator compartment can be reached as follows: " unscrew the light cover securing screws; " unhook the moving part by pressing it as shown in the figure. If the door is open and the light does not come on, check that the bulb is properly screwed in; if it still does not work, replace the bulb with one of the same power. [. . . ]