User manual KENWOOD CD-324M

[. . . ] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Chapter 1 For the United Kingdom Factory fitted moulded mains plug 1. The mains plug contains a fuse. 2. The fuse cover must be refitted when replacing the fuse in the moulded plug. Chapter 2 Chapter 3 3. Do not cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension lead or adapter, or consult your dealer. [. . . ] We recommend to execute this mode before playback after discs have been exchanged. To display the title on a LCD remote control unit (provided with a KENWOOD Receiver or optional), perform the all data read operation first, and operate the LCD remote control unit with the door left closed. For the operation of the LCD remote control unit, refer to the instruction manual provided with your receiver or LCD remote control unit. 1 Press the MODE button. MODE Chapter 5 2 Select "ALL DATA READ". Each press switches the modes as follows: 1 MUSIC TYPE 2 USER FILE 3 DISC SEARCH 4 TITLE INPUT 5 ALL DATA READ 6 ALL INFORMATION DISC SKIP DOWN UP ALL DATA READ3 Search in progress or reading information The display flashes. Chapter 6 DDISCCREADING3 3 Set the input. When the disc is CD-TEXT D001:: CDATEXT3 SET ÷ Repeat the above procedure so that the complete disc information is read into the CD player. ÷ In the case of a non-CD-TEXT disc, the "D001:NO CD TEXT" display will appear for approx. 3 seconds. Chapter 7 To quit ALL DATA READ mode Press the 7 button. 1. If blinking "PLEASE WAIT" is displayed when the disc door is opened, do not attempt to change the disc. Notes Normal play (TRACK mode) Normal play (TRACK mode) 19 Chapter 1 Playing tracks in order from track No. 1 Use the following procedure to play a CD in the original order of tracks from track No. 1. Chapter 2 1 Select the disc. DISC SKIP DOWN UP Previous disc Next disc ÷Each press of a button increases (or decreases)the disc number. ÷When the disc corresponds to CD-TEXT, or when the disc title has been registered, the disc title will be displayed with scrolling. "Registration of Title" · Chapter 3 Display when disc No. 123 is selected Go to step 2 within 8 sec. D123 1:23 2 Start playback. ENTER Chapter 4 6 ÷ When the disc corresponds to CD-TEXT, or when the track titles have been registered, the track title is displayed. Chapter 5 To pause playback ENTER To stop playback 7 6 Chapter 6 ÷ Each press pauses and plays the CD alternately. Chapter 7 Normal play (TRACK mode) 20 Direct disc selection 1 Press the DISC SELECTOR button. DISC SELECTOR X Press the numeric buttons in the following order. . . Disc No. 100 : 1, 0, 0 Chapter 1 Within 8 seconds! How to input numeric values The input method for this product is of two different types. One can either use the traditional KENWOOD +10 button approach, or direct numeric input. 2 Input the disc number. 1 H 2 I 3 J 4 K Special input method for CD player with 200-disc changer To input 42 : 4, 2 To input 115 : 1, 1, 5 To input 200 : 2, 0, 0 5 L 6 M 7 N 8 O +100 S Chapter 2 9 P 0 Q +10 R Same input method as other KENWOOD products To input 42 : +10, +10, +10, +10, 2 To input 115 : +100, +10, 5 To input 200 : +100, +100 Within 8 seconds! 3 Start playback. ENTER 6 Chapter 3 What is the "normal play TRACK mode"? Chapter 4 Playback is made from the first track. from the beginning. Chapter 4 Chapter 5 3 Select the track number. 1 Input the track number. 1 H 2 I 3 J 4 K 5 L 6 M 7 N 8 Press the numeric buttons in the following order. . . Track No. 8 : 8 Track No. 14 : 1, 4 Track No. 20 : 2, 0 O +100 S P GM 0 1 ED 2 0 01T- -C ÷ To program the entire disc, press the SET button without inputting the track number. ÷ Program other tracks in the desired order by repeating steps 2 and 3. ÷ If you make a mistake, press the CLEAR button and restart from step 2. ÷ When the disc corresponds to CD-TEXT, or when the disc title has been registered, the track title is displayed. Tracks can be selected by the track title. 9 P 0 Q +10 R Chapter 6 Within 8 seconds! 2 Set the input. SET Chapter 7 4 Start playback. ENTER 6 ÷ Tracks will be played in the order they are programmed. ÷ When the 4 or ¢ button is pressed during playback, the track will be skipped in the direction of the pressed button. Programming tracks in desired order (PGM mode) 25 Chapter 1 To check the programmed tracks SPACE /CHECK Chapter 2 P GM 0 1 ED 2 00 T 03 D ÷ Each time the button is pressed, the program No. ÷ The previous display resumes in a few seconds. Chapter 3 To add a track to the program 1 Set the CD player to stop mode. 2 Perform steps 2 and 3 of "Programming tracks in desired order". is entered, the track will be added to the end of the existing program. Chapter 4 To change a track in the program 1 Set the CD player to stop mode. 2 Press the CHECK button. SPACE /CHECK ÷ Press the CHECK button repeatedly until the program No, to be changed is displayed. Chapter 5 P GM 0 1 ED 2 00 T 03 D 3 Perform steps 2 and 3 of "Programming tracks in desired order". ¢ ÷ Press it while the "PGM01" indicator blinks. [. . . ] ­ ­ Increase the separation between the equipment and receiver. ­ ­ Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ­ ­ Consult the dealer or an experienced radio / TV technician for help. Chapter 2 For the U. S. A. FCC Compliance Notice Compact Disc Player, CD-4700M, CD-4260M, CD-425M Those devices complies with Part 15 of FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. [. . . ]