User manual KENWOOD DMC-J7R

[. . . ] DMC-J7R PORTABLE MINIDISC RECORDER INSTRUCTION MANUAL KENWOOD CORPORATION In regard to the power supply Do not use a power source other than the specially provided AC adaptor or the optional battery case or the optional car battery adaptor. TINSE1638AFZZ A9805. 2. 2MNS. SM B60-4023-08 EN 99/12 11 10 9 8 7 6 5 4 3 2 1 98/12 11 10 9 8 7 6 5 4 INTRODUCTION Unpacking Read this page carefully to ensure safe operation Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. Only the consignee (the person or company receiving the unit) can file a claim against the carrier for shipping damage. [. . . ] q The edited contents can be stored on the disc after several editing steps have been performed. Cautions: q Whilst "TOC" or "TOC EDIT!" is displayed, do not do any of the following. If you do, the changes in the recorded or edited contents will be lost if the TOC information is not recorded properly. q If the AC adaptor is unplugged or a power failure occurs whilst recording (before the TOC information has been written on the disc), the new recording will be erased. When a new recording is added to a MiniDisc in a position where TOC information already exists, the added recording will be erased. 23 PLAYING A MINIDISC Headphones For the For the left (L) right (R) BASS/DELETE To the socket VOLUME/NAME Remote control unit BASS 1 Insert the headphones plug firmly into the headphones socket on the remote control unit. 2 Plug the remote control unit into the socket on the main unit. q Since the remote control unit plug has only one correct orientation, plug it in as shown in the drawing. q When the recordable MiniDisc write protection tab is closed (page 12) q When the auto-play function has been cancelled (page 38) 4 Press the + button to increase the volume and the - button to decrease the volume. 3 Load a MiniDisc in the direction indicated by the arrow on the MiniDisc, with the label side facing up. (Insert the MiniDisc firmly, until a click is heard. ) q The power will be turned on automatically, and playback will start from the first track. (Auto-play function) Track number Volume (0 - 30) 5 Adjust the bass level. Each time the BASS/DELETE button is pressed, the tone will be switched as follows: Track name (Nothing will be displayed for MiniDiscs that do not contain track names. ) BASS 1 BASS 2 BASS 3 Bass sounds are emphasised slightly. Bass emphasis is cancelled. q After playback of the last track has finished, the unit will stop automatically. Playback does not MiniDisc is inserted: start when a BASS OFF Press the 38 button. In the following cases, the auto-play function will not work. q When recording, it is impossible to adjust the bass level (Bass emphasis is cancelled). q The most recent volume or bass settings are saved when the power is turned off. 24 To interrupt playback: Press the 38 button during playback. q To resume playback, press the 38 button again. To turn off the power: Press the s / OFF button whilst in the stop mode. q If the unit is not operated for at least 2 minutes whilst in the stop mode, the power will be turned off automatically. To stop playback: Press the s / OFF button. q When you press the 38 button to resume playback, it will start at the point on the disc where playback was halted (Resume function). However, if the MiniDisc is removed and reinserted, playback will start from the first track. When using the unit with just the batteries in the battery case: q The auto-play function will not work. q Even if a MiniDisc is replaced whilst the power is turned off, the random or repeat play settings will remain unchanged in memory. Precautions when making connections: q Do not use any remote control unit, except for the one included with this unit. Interrupted sound: q This product is designed to eliminate interruptions in the sound which can be caused by vibrations. However, if the unit is continuously exposed to vibrations or mechanical shock, the sound may be interrupted momentarily. When the sound is distorted: q If the volume is too high whilst the bass is being emphasised, the sound may be distorted, depending on the music on the track. [. . . ] q Since a track number is currently being located or written to, the unit cannot accept your command. q There is no space left for recording character information (track names, disc names, etc. ). q Recording cannot be performed correctly due to vibration or shock in the unit. Remedy q Charge the rechargeable battery or replace the alkaline batteries (or use the AC adaptor for power). [. . . ]