User manual KENWOOD KAC-746
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual KENWOOD KAC-746. We hope that this KENWOOD KAC-746 user guide will be useful to you.
Manual abstract: user guide KENWOOD KAC-746
Detailed instructions for use are in the User's Guide.
[. . . ] · Do not touch the unit during use because the surface of the unit becomes hot and may cause burns if touched.
· Do not open the top or bottom cover. · Do not install the unit in places it is exposed to direct sunlight, high heat or humidity, water may splash over it, or dust exists.
NOTE
· If you have difficulty in installing this unit in your vehicle, contact your Kenwood dealer.
Cleaning the unit
· If the surface is dirty, wipe it clean with a silicon cloth or soft dry cloth with the power off.
2CAUTION
Do not use hard cloths or paint thinner, alcohol, or other volatile solvents. These may damage external surfaces or remove indicator characters.
2CAUTION
Take the following precautions to keep the unit in proper working order.
· Be sure the unit is connected to a 12V DC power supply with a negative ground connection.
Accessories
Part name
Battery cable (Yellow) (6 m) Ground cable (Black) (1 m) Self-tapping screws (ø4 × 16 mm) Terminal cover (Power terminal)
External View
Number of Items
1 1 4 1
Part name
Round terminal (Large) Round terminal (Medium) Round terminal (Small) Grommets
External View
Number of Items
1 2 1 1
2
Installation procedure
1. [. . . ] This unit is compatible with a large variety of systems by combining the switches and functions described in the following.
1
FUSE(30A) POWER IN
5
BRIDGED
GND
BATT P. CON(REMOTE)
SPEAKER OUTPUT BRIDGED A A B L R B
LEFT
RIGHT
SPEAKER LEVEL INPUT LEFT RIGHT A SPEAKER LEVEL INPUT A B B L R
234 8 9 0 !@
100 80 150 100 80
6
7
INPUT SENSITIVITY(V)
0. 5 0. 3
GND MONO L
A LINE IN B
A+B L
LINE OUT INPUT SENSITIVITY(V)
0. 5 1. 0 0. 3
FILTER
OPERATION
1. 0 MIN STEREO MONO(Lch) L+R MAX
OPERATION R AB A R
FILTER
OFF HPF LPF
100 80
80 150 100
150 OFF HPF LPF 50 LPF 200 50 HPF 200
150 50 LPF 200 50 HPF 200
4 CHANNEL POWER AMPLIFIER
MIN
MAX STEREO MONO(Lch) L+R
FREQUENCY(Hz)
FREQUENCY(Hz)
CONTROL A
INPUT SELECTOR
CONTROL B
Amplifier A
# $ %^
Amplifier B
1 Fuse (30 A) 2 Battery terminal 3 Ground terminal 4 Power control (REMOTE) terminal 5 Amplifier A speaker output terminals 6 Amplifier B speaker output terminals 7 Speaker level input terminals 8 FREQUENCY control
When the FILTER switch is set to the HPF (High-Pass Filter) or LPF (Low-Pass Filter) position, the threshold frequency can be adjusted with this control.
9 FILTER switch
High-pass or low-pass filtering can be applied to the speaker output according to the setting of this switch.
0 OPERATION switch
The amplification methods of the signals input to amplifiers A and B can be selected independently according to the setting of this switch.
4
· STEREO position:
The amplifier can be used as a stereo amplifier.
· L+R position:
The input left and right signals are combined before being amplified. Use this position when the unit is used for subwoofer speakers or the L+R (monaural) sound is required.
· MONO (Lch) position:
Amplifies the signal input from the left side only. Set to this position and make bridged connections to use as a high-power monaural amplifier. INPUT SENSITIVITY control
Set this control according to the pre-output level of the center unit connected with this unit, or to the maximum power output of the genuineaccessory car stereo. NOTE For the pre-output level or the maximum power output, refer to the "Specifications" in the instruction manual of the center unit.
25 10 15 0. 5 0. 3
1. 0 MIN (W) MAX
@ RCA cable ground lead terminal # INPUT SELECTOR switch
This switch selects the input method of the signals to be amplified by amplifiers A and B.
· A B position:
Amplifies both of the signals input to amplifiers A and B.
· A position:
Amplifies only signal input amplifier A with both amplifiers A and B.
$ Amplifier A LINE IN terminal % Amplifier B LINE IN terminal ^ LINE OUT terminal
These jacks output respectively the signals input to amplifiers A and B. They always output the stereo signals regardless of the position of the OPERATION switch.
Protection function
This unit is equipped with a protection function for protecting this unit and your speakers from various accidents or problems that can occur. When the protection function is triggered, the Power indicator goes off and the amplifier stops operating. s Power indicator:
When the power is turned on, the Power indicator lights. If the Power indicator does not light when the power is turned on, the protection function may be activated. Power indicator
s The protection function activates in the following situations:
· When a speaker output contacts ground. · When the unit malfunctions and a DC signal is sent to the speaker output. · When the temperature of internal parts exceeds 120°C (248°F). · When a ground cable of the center unit (cassette receiver, CD receiver, etc. ) or this unit is not connected to a metal part serving as an electrical ground passing electricity to the battery's negative - terminal.
5
Connection
sRCA cable connection
BLINE IN (Rear) CENTER UNIT (Cassette receiver, CD receiver, etc. ) Power control cable
POWER IN
2CAUTION Do not connect cables and leads to both RCA cable input jacks and the speaker input terminals simultaneously, for this may cause malfunction or damage.
ALINE IN (Front) RCA cable (Commercially available part)
GND
BATT P. CON(REMOTE)
A Left input (White)
INPUT SENSITIVITY(V)
0. 5 0. 3 1. 0 MAX
B Left input (White)
GND MONO L A LINE IN B A
{B
L
LINE OUT INPUT SENSITIVITY(V)
0. 5 0. 3
100 80
100 80 150
FILTER
OPERATION
1. 0 MIN STEREO MONO(Lch) L {R
OPERATION R AB A R
FILTER
OFF HPF LPF
100 80
80 150 100
150 OFF HPF LPF 50 LPF 200 50 HPF 200
150 50 LPF 200 50 HPF 200
4 CHANNEL POWER AMPLIFIER
MIN
MAX STEREO MONO(Lch) L {R
FREQUENCY(Hz)
FREQUENCY(Hz)
CONTROL A
INPUT SELECTOR
CONTROL B
A Right input (Red) B Right input (Red) RCA cable ground terminal 2CAUTION When using an RCA cable with Do not use this terminal for power source a ground lead attached, connect grounding. [. . . ] · Check connections by referring to "Protection function". · Connect them properly checking the + / - of the terminals and cables well. · Connect the speaker cable again so that it is not pinched by anything. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE KENWOOD KAC-746
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual KENWOOD KAC-746 will begin.