User manual KENWOOD KDC-C660

[. . . ] The user could lose the authority to operate this equipment if an unauthorized change or modification is made. English | 3 Safety precautions 2WARNING To prevent injury or fire, take the following precautions: · To prevent a short circuit, never put or leave any metallic objects (such as coins or metal tools) inside the unit. Lens Fogging When you turn on the car heater in cold weather, dew or condensation may form on the lens in the CD player of the unit. Called lens fogging, this condesnation on the lens may not allow CDs to play. In such a situation, remove the disc and wait for the condensation to evaporate. If the unit still does not operate normally after a while, consult your Kenwood dealer. 2CAUTION To prevent damage to the machine, take the following precautions: · Make sure to ground the unit to a negative 12V DC power supply. [. . . ] (For the finalization process refer to your CD-R/CD-RW writing software, and your CDR/CD-RW recorder instruction manual. ) Burrs Burrs CD storage · Do not place CDs in direct sunlight (On the seat or dashboard etc. ) or where the temperature is high. · Store CDs in their cases. CD accessories Do not use disc type accessories. CD cleaning Clean from the center of the disc and move outward. 6| English General features Release button VOL Control knob ATT Q SRC CLK LOUD indicator Clock display ATT indicator Power Turning ON the Power Press the [SRC] button. Turning OFF the Power Press the [SRC] button for at least 1 second. Volume Increasing Volume Turn the [VOL] knob clockwise. Decreasing Volume Turn the [VOL] knob counterclockwise. Selecting the Source Press the [SRC] button. Source required Tuner CD Standby (Illumination only mode) Display "TUnE" "CD" "STBY" Attenuator Turning the volume down quickly. When the Attenuator is ON, the "ATT" indicator blinks. English | 7 General features System Q Selecting the best sound setting preset for different types of music. 4 Adjust the Audio item Turn the [VOL] knob. Adjustment Item Display Range Bass level "BAS" ­8 -- +8 Middle level "MID" ­8 -- +8 Treble level "TRE" ­8 -- +8 Balance "BL" Left 15 -- Right 15 Fader "FD" Rear 15 -- Front 15 Exit Audio Control mode (Volume control mode) 1 Select the source to set Press the [SRC] button. 2 Select the Sound type Press the [Q] button. When you press the button once, the current sound setting is displayed. Sound setting Flat Rock Pops Easy Top 40 Jazz Display "FLAT" "ROCK" "POPS" "EASY" "TP40" "JAZZ" 5 Exit Audio Control mode Press any button. Press a button other than the [VOL] knob, [SRC], [0] and [ATT] button. Audio Setup Setting the Sound system, such as Volume offset and Loudness. · "USER": The values set on the <Audio Control> (page 8). When the System Q setting is changed, the Bass, Middle, and Treble set in audio control replace the System Q values. Each time you push the knob toward [FM], it switches between the FM1, FM2, and FM3 bands. 3 Tune up or down band Push the Control knob towards [4] or [¢]. · During reception of stereo stations the "ST" indicator is ON. English | 11 Tuner features Station Preset Memory Putting a station in the memory. CRSC (Clean Reception System Circuit) Temporarily have reception alternate from stereo to mono to reduce multi-path noise when listening to the FM station. When CRSC is ON, the CRSC indicator is ON. 1 Select the band Push the Control knob towards [FM] or [AM]. 2 Select the frequency to put in the memory Push the Control knob towards [4] or [¢]. 3 Put the frequency in the memory Press the desired [1] -- [6] button for at least 2 seconds. On each band, 1 station can be put in the memory on each [1] -- [6] button. Auto Memory Entry Putting stations with good reception in the memory automatically. 1 Select the band for Auto Memory Entry Push the Control knob towards [FM] or [AM]. 2 Open Auto Memory Entry Press the Control knob for at least 2 seconds. · If the console has a lid, make sure to install the unit so that the faceplate will not hit the lid when closing and opening. · If the fuse blows, first make sure the wires aren't touching to cause a short circuit, then replace the old fuse with one with the same rating. · Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals. · Connect the speaker wires correctly to the terminals to which they correspond. The unit may be damaged or fail to work if you share the - wires or ground them to any metal part in the car. · When only two speakers are being connected to the system, connect the connectors either to both the front output terminals or to both the rear output terminals (do not mix front and rear). For example, if you connect the + connector of the left speaker to a front output terminal, do not connect the - connector to a rear output terminal. [. . . ] After checking for short circuits in the wires, replace the fuse with one with the same rating. If there's no media in this unit, you can't switch to each source. Connect the wire correctly, referring to the section on <Connecting Wires to Terminals>. Even if Loudness is turned ON, high-pitched tone isn't compensated for. [. . . ]