User manual KENWOOD KRF-7300D

[. . . ] AUDIO-VIDEO CONTROL CENTER KRF-V9300D KRF-V8300D KRF-V7300D INSTRUCTION MANUAL Declaration of Conformity with regard to the EMC Directive 2004/108/EC Manufacturer: Kenwood Corporation 2967-3 Ishikawa-machi, Hachioji-shi, Tokyo, 192-8525 Japan EU Representative's: Kenwood Electronics Europe BV Amsterdamseweg 37, 1422 AC UITHOORN, The Netherlands © B60-5740-00/00 (EW/XW) Safety precautions ¤ Caution : Read this page carefully to ensure safe operation. Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 240 V only Europe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 230 V only Unpacking Unpack the unit carefully and make sure that all the accessories are present. FM indoor antenna (1) Before use WARNING : TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN AM loop antenna (1) CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE" WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A RISK OF ELECTRIC SHOCK TO PERSONS. [. . . ] After adjusting the levels of all the speaker channels, press [ENTER] to enter the settings. 2 Select the unit of distance. [MULTI CONTROL 2/3] [ENTER] Display "UNIT Meters" "UNIT Feet" "Return" Setting Measurement in meters. Returns to Setup Menu. 3 Set the distance. · If you have a commercially available acoustic pressure meter, set the meter-reading unit to "C" and adjust the speaker channel levels so that the noise level is 75 dB. Refer to the table above for the distance from each speaker to this unit. Use [MULTI CONTROL 2/3] to select the speaker. Use [MULTI CONTROL /5] to set the distance. The distance can be set in the range of 0. 03 to 9. 0 meters (0. 1 to 30. 0 ft) in 0. 03-meter (0. 1-feet) increments. 4 Repeat step 3 for each speaker until the distances of all speakers are set. 5 Press [ENTER] to enter the setting. English 37 Other setups Subwoofer Remix ­"Subw Re-Mix"­ Mixes the bass tone of other channels to the subwoofer channel. Crossover ­"Crossover"­ The crossover frequency is the lower limit of the bass frequencies reproduced from the speakers set to "Normal" in the <Speaker configuration ­"SP Setup"­>. The frequencies below the set crossover frequency are output from other speakers (those set to "Large" and the subwoofer). 1 Select "Subw Re-Mix". [SETUP] [MULTI CONTROL 2/3] 1 Select "Crossover". [SETUP] [ENTER] [MULTI CONTROL 2/3] Setup 2 Set the Subwoofer Remix. Use [MULTI CONTROL /5] to select whether or not Subwoofer Remix is used. [ENTER] 2 Set the crossover frequency. Use [MULTI CONTROL /5] to select crossover frequency. [ENTER] The frequency is selected from 40Hz to 200Hz in10Hz step. [ENTER] Display "SW RE-MIX On" "SW RE-MIX Off" Setting Sets Subwoofer Remix to ON. In this case, the bass frequencies are output only from the front speakers. LFE (Low Frequency Effect) level ­"LFE Level"­ Low frequency effect signal is used exclusively for giving the field effect of bass tone in the Dolby Digital and DTS signal. · Subwoofer Remix cannot be setup if the Subwoofer is set to "SUBW Off" or the Front speakers are set to "FRNT Normal". 1 Select "LFE Level". [SETUP] [MULTI CONTROL 2/3] [ENTER] 2 Set the LFE level. Use [MULTI CONTROL /5] to select the LFE level. [ENTER] The level is adjusted from 0dB to -10dB in1dB step decrements. 38 KRF-V9300D/KRF-V8300D/KRF-V7300D Input assignment ­"Assignment"­ The input source for the signal output at the CD (ASSIGNABLE) terminal can be assigned: CD, VIDEO1 or AUX. 1 Select "Assignment". [SETUP] [MULTI CONTROL 2/3] [ENTER] Setup 2 Select the input source to be assigned. Use [MULTI CONTROL /5] to select the input. [ENTER] Display "OPT1 CD" "OPT1 VIDEO1" "OPT1 AUX" Setting Assign CD as the input source Assign VIDEO1 as the input source Assign AUX as the input source Audio delay ­"Audio Delay"­ If the monitored video is delayed in time with respect to the audio from the speakers, the audio output timing can be delayed. 1 Select "Audio Delay". [SETUP] [MULTI CONTROL 2/3] [ENTER] 2 Set the delay time. Use [MULTI CONTROL /5] to select the delay time. [ENTER] The delay time is adjusted from 0ms to 300ms in 10ms step. English 39 HDMI setup The HDMI setup is required to use the component connected to the HDMI terminal or to use the HDMI control functions. (See <HDMI input setup ­"HDMI Input"­>. ) HDMI setup ­"HDMI Setup"­ The HDMI control functions can be set. 1 Enter the HDMI Setup mode. [SETUP] Use [MULTI CONTROL 2/3] to select "HDMI Setup". SETUP ENTER Setup MULTI CONTROL /// [ENTER] 2 Select an item to set. [MULTI CONTROL 2/3] [ENTER] Display "Audio Out" "Audio Delay" "HDMI Link" "Power CTRL"*1 Setting Sets the HDMI audio output destination. Allows the TV to control this unit including the volume levels from the speakers. Returns to Setup Menu. HDMI input setup ­"HDMI Input"­ The HDMI inputs can be enable or disabled individually. Enabling an HDMI input makes it possible to set the HDMI function and use the HDMI control functions. 1 Select "HDMI Input". [SETUP] [MULTI CONTROL 2/3] "TV CTRL"*2 "Return" 1 [ENTER] 2 Select an HDMI input source (DVD or VIDEO2) and its HDMI audio and video inputs. Use [MULTI CONTROL 2/3] to select the input source (DVD or VIDEO2). * This item can be set when "HDMI Link" is set to "On". *2 This item can be set when "Power CTRL" is set to "On". 3 Set each item. See next page for each HDMI control item. Use [MULTI CONTROL /5] to set the HDMI audio and video inputs. [ENTER] Display (When in DVD input source/ When in VIDEO2 source) "DVD A/V" "VIDEO2 A/V" "DVD Video" "VIDEO2 Video" "DVD Off" "VIDEO2 Off" Setting Enables the HDMI inputs for both audio and video. The audio input becomes the digital (optical or coaxial) or analog audio input. The video input becomes the analog video input (VIDEO, S-VIDEO or COMPONENT VIDEO terminal) and the audio input becomes the digital (optical or coaxial) or analog audio input. 40 KRF-V9300D/KRF-V8300D/KRF-V7300D Audio Out This function selects whether the output destination of the audio input is the TV or this unit. HDMI Link This function selects whether or not the volume control and input selection of this unit are interlocked with the operations of the connected components. 1 Select "Audio Out" in <HDMI setup ­"HDMI Setup"­ > , . 1 Select "HDMI Link" in <HDMI setup ­"HDMI Setup"­> , . 2 Set the HDMI audio output destination. [MULTI CONTROL /5] [ENTER] 2 Set the HDMI link on or off. [MULTI CONTROL /5] Setup [ENTER] Display "AUDIO OUT AMP" "AUDIO OUT TV" Setting Outputs the audio from the speakers connected to this unit. Display "HDMI LINK On" "HDMI LINK Off" Setting The HDMI control functions are used. The HDMI control functions are not used. · Audio Out can be set when TV Control is set to off. · If "AUDIO OUT TV" is selected and the audio is not output or is interfered with by noise, set the audio output of the player component to PCM. · If "AUDIO OUT TV" is selected, adjust the volume on TV. When "HDMI LINK On" is selected, the HDMI indicator on the front panel lights blue. [. . . ] MONITOR FM tuner section Tuning frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87. 5 MHz ­ 108. 0 MHz AM tuner section Tuning frequency range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 531 kHz ­ 1, 602 kHz iPod section Maxmum current drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 500 mA General Power consumption KRF-V9300D. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275 W KRF-V8300D/KRF-V7300D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 W Standby power consumption (HDMI Link :Off) . . . . . . . . . . . . . less than 0. 4 W Dimensions (KRF-V9300D) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . W: 440 mm (17-5/16") . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]