User manual KENWOOD KRF-A4020

[. . . ] AUDIO RECEIVER KRF-A4020 INSTRUCTION MANUAL About the supplied remote control (RC-R0708) . . Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). [. . . ] To change the source name associated with the MD/TAPE1 jacks to "MD", follow the steps below: 1 Use the INPUT SELECTOR knob to select "TAPE 1". · To return to the original indication, repeat the above procedure. · When selecting an input source by using the remote control , press the desired input selector key. · The INPUT SELECTOR on the front panel of the receiver always cycles through all inputs. 2Start playback from the selected source. 3Use the VOLUME CONTROL (VOLUME UP , DOWN) to adjust the volume. · The sound of input source cannot be listened to with TAPE2/MONITOR is ON. Normal playback KRF-A4020 (En/E2T) Adjusting the sound Adjusting the tone Use the following procedure to adjust the bass and treble levels. (Press the SOUND key once. ) TREBLE : Select this to adjust the high frequency range. A B SOURCE DIRECT playback Use this function to pass the source material direct to the amplifier, by passing any audio processing. A B S. DIRECT 11 · Switch to another input source to cancel SOURCE DIRECT (S. DIRECT) playback. BAss +4 To cancel Press the SOURCE DIRECT (S. DIRECT) key again. 2 Use the MULTI CONTROL to adjust the sound quality. · The bass and treble levels are adjustable from -10 to +10 in 2 step increments. · The adjustment item is displayed for approximately 8 seconds. Listening with headphones Operations Other 1 Press the SPEAKERS A or B key so that the speaker indicator goes off. Make sure the SPEAKERS indicators are turned off. Once-touch low frequency emphasis (BASS BOOST) Use the following procedure to emphasize the bass and create a richer sound. SP. TAPE1 2 Connect headphones to the PHONES jack. PHONES Press the BASS BOOST key. SP. A B BAss + 1) · Press the BASS BOOST key once to select the maximum (+10) low frequency emphasis setting. Switching back to the previous setting Press the BASS BOOST key again. 3 Use the VOLUME CONTROL (VOLUME UP, DOWN) to adjust the volume. To adjust the BALANCE Muting the sound MUTE lets you mute the sound of the speakers. A B MUTE The mode for adjusting the volume balance between the left and right. 2 Use the MULTI CONTROL to adjust the balance. TAPE1 · Muting can also be cancelled by adjusting the volume. Indicates the balance setting. Indicates the center. To cancel Press the MUTE key again so that the "MUTE" indicator goes off. SP. A B L-- t- R Preparations TAPE1 Recording KRF-A4020 (En/E2T) 12 INPUT SELECTOR TAPE2/MONITOR function You can connect a cassette deck or graphic equalizer to the TAPE2/MONITOR jacks of the receiver. If a graphic equalizer is connected, the TAPE2/MONITOR key should be left in the on position. Alternately, if a cassette deck equipped with a 3-head system is connected to theTAPE2/ MONITOR jacks, you will be able to monitor the justrecorded signal while making recordings on the cassette deck. By switching the TAPE2/MONITOR key on and off, you can compare the sound of the source signal and the just-recorded signal. For more information, refer to the instruction manual of the connected component. · The equalizer effect can be applied to the played audio but cannot be recorded together with the audio signal. · Copy from "TAPE 2" to "TAPE 1" is not possible. Preparations Operations Other TAPE2 /MONITOR MULTI CONTROL SOUND MULTI CONTROL SOUND TAPE2 /MONITOR Input level adjustment (when using the monitor function) Recording audio Recording a music source 1 Use the input selector (INPUT SELECTOR) to select the source (other than "TAPE 1") you want to record. 3 Start playback, then start recording. If the input level while using the monitor function is too high, adjust the input level as described below. The input level cannot be adjusted when in the source direct playback mode. [. . . ] · Connect properly referring to "Setting up the system". · Wait until recording has completed. 19 Memory back up function Please note that the following items will be deleted from the unit's memory if the power cord is disconnected from the AC outlet or the main power switch is turned off for approximately 3 days. · Power mode · Input selector settings · Volume level · Broadcast band · Frequency setting · Preset stations Other Operations Preparations Specifications 20 [ AUDIO section ] Rated power output during STEREO operation (DIN) 1 kHz, 0. 7 % at 4 . . . . . . . . . . . . . . . . . . . . . . . . 0. 02 % (1 kHz, 50 W, 4 ) Signal to noise ratio PHONO (MM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]