User manual KENWOOD KRF-V7030D

[. . . ] AUDIO VIDEO SURROUND RECEIVER KRF-V7030D KRF-V6030D KRF-V5030D KRF-V4530D INSTRUCTION MANUAL KENWOOD CORPORATION This instruction manual is used to describe multiple models listed above. Model availability and features (functions) may differ depending on the country and sales area. B60-4602-00 (EN) Remote Control Other Operations Preparations Before applying the power Units are designed for operation as follows. Caution : Read this page carefully to ensure safe operation. 2 Unpacking Unpack the unit carefully and make sure that all accessories are put aside so they will not be lost. If your unit is damaged or fails to operate, notify your dealer immediately. If your unit was shipped to you directly, notify the shipping company without delay. [. . . ] For more information, refer to the instruction manual of the connected component. 3 Use the VOLUME CONTROL (VOLUME) to adjust the volume. Recording Recording video 1 Use the INPUT SELECTOR to select the video source (other than "VIDEO1") you want to record. · With certain video software, recording may not be normal due to the copy guard condition. · Recording music in M-REC MODE DIMMER 19 Recording audio (digital sources) Switch on the REC MODE to record a digital input source. When the digital mode changes during recording in the A- REC MODE, the audio may be interrupted momentarily. To record the audio from the beginning of the digital mode change, use the M-REC MODE. With a model that is not compatible with DTS, no audio is reproduced even when the DTS signals are input. INPUT SELECTOR 1 Use the input selector to select the source (CD, DVD, VIDEO2, or VIDEO3) you want to record. 4 Press and hold the DIMMER key for more than 2 seconds to select the M-REC MODE. · The mode changes every 2 seconds as shown below. Recording music in A-REC MODE DIMMER 1REC MODE off : 2A-REC MODE : 3M-REC MODE : INPUT SELECTOR 1 Use the INPUT SELECTOR to select the source (CD, DVD, VIDEO2, or VIDEO3) you want to record. 3 Press and hold the DIMMER key for more than 2 seconds to select the A-REC MODE. 1REC MODE off : 2A-REC MODE : The digital input record mode is switched off. The digital input signals (DTS, Dolby Digital, or PCM) are identified automatically and converted into stereo signals that are ready for recording. The input signal type at the moment this mode is selected is held throughout this mode. FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP The digital input record mode is switched off. The digital input signals (DTS, Dolby Digital or PCM) are identified automatically and converted into stereo signals that are ready for recording. The input signal type at the moment this mode is selected is held throughout this mode. FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP 5 Play the source from the beginning and start recording. · If the audio reproduction stops in the middle due to change in the input signals, etc. , press the DIMMER key. 3M-REC MODE : AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. · If the audio reproduction stops in the middle due to change in the input signals, etc. , press the DIMMER key. Operations Listening to radio broadcasts 20 Tuning (non-RDS) radio stations Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory, see the section entitled, "Using RDS". Using RDS (Radio Data System) RDS is a system that transmits useful information (in the form of digital data) for FM broadcasts along with the broadcast signal. Tuners and receivers designed for RDS reception can extract the information from the broadcast signal for use with various functions, such as automatic display of the station name. MULTI CONTROL KRF-V6030D/ V5030D/ V4530D INPUT SELECTOR RDS functions: PTY (Program Type Identification) Search £ Automatically tunes to a station that is currently broadcasting the specified program type (genre). PS (Program Service Name) Display Automatically displays the station name transmitted by the RDS station. [. . . ] · If the component is already on, pressing the source POWER keys will turn it off. Setup code chart 34 TV Setup codes Maker BLAUPANKT GRUNDIG MIVER NOKIA NORDMENDE PHILIPS SABA SCHNEIDER TELEFUNKEN THOMSON AKAI FENNER FISHER HITACHI INNO-HIT IRRADIO JVC MAGNAVOX OKANO ORION PANASONIC SAMSUNG SANYO SHARP SONY TOSHIBA Setup codes 401 402 401 403 404, 405 406 404, 407 408 407, 409, 410 411 408 412 413 414, 415 416 408 417 406 416 418 419, 420 421 413 422 423, 424, 425, 426, 427 428 VCR Setup codes Maker BLAUPANKT GRUNDIG LOEWE NOKIA NORDMENDE PHILIPS SABA SIEMENS TELEFUNKEN AIWA BELL+HOWELL CGM DIGTAL FISHER G. E. HITACHI JVC MAGNAVOX MITUBISHI PANASONIC PHONOLA SAMSUNG SANYO SHARP SONY TOSHIBA Setup codes 501 502 503, 504 505 506, 507, 508 509 510 502 511, 512 513 514 514, 515 515 514 516 517, 518 519 501, 515 520, 521, 522, 523 524 515 525, 526 514 527, 528 529, 530, 531 532 DVD Setup codes Maker JVC SONY PIONEER PANASONIC KENWOOD TOSHIBA PHILIPS Setup codes 801 802 803 804 804, 805, 808 806 807 CDR Setup codes Maker KENWOOD PHILIPS PIONEER Setup codes 533 533 534 Remote Control In case of difficulty Remote control unit Symptom Certain inputs cannot be selected using the remote control. Cause · No setup codes registered at for the respective input(s). · The remote control unit is too far away from the main system, controlling angle is too large, or there is an obstacle between the receiver and the remote. [. . . ]