User manual KENWOOD KRF-V7773D

[. . . ] VR-4090/VR-4080 KRF-V7773D This instruction manual is used to describe multiple models listed above. Model availability and features (functions) may differ depending on the country and sales area. B60-4487-10 01 CH (K, P, T, M, X, Y) OC 9911 Connecting and Setting Up Your New Kenwood Audio-Video Receiver Welcome to the Connection and Setup Guide for your new Kenwood Audio-Video Receiver. The VR-4090/VR-4080/KRF-V7773D offers 3 kinds of 5. 1channel digital decoding: · · Dolby® Digital, for the hundreds of currently available Dolby Digital DVDs and LaserDiscs. DTS®, a well-established multichannel format in movie theaters, is available for home theater on LaserDisc and DVD. [. . . ] focuses on the connections from your VCR to the front of the VR-4090/VR-4080/ Please refer to your camcorder or VCR's inmore detail about its connection jacks and PRO LOGIC 3 STEREO These instructions describe how to connect a camcorder or VCR quickly and probably temporarily to the front of the receiver. If you want a less cluttered and more permanent connection, see "Can I Connect an Additional VCR Permanently?", below. To Connect a Camcorder or Additional VCR: Connect the audio and video cables from the camcorder or VCR's Audio and Video jacks to the receiver's front panel jacks as shown to the left. VOLUME CONTROL Can I Connect an Additional VCR Permanently? Yes. To do so, follow the instructions under "To Connect a Secondary VCR:" on page 13. 29 DOWN UP S VIDEO AV AUX VIDEO L - AUDIO - R (or additional VCR) AUDIO OUT VIDEO OUT S-VIDEO OUT Connections Chapter One : Connecting Your Devices Connecting an External IR Receiver and IR Repeaters (VR-4090 and VR-4080 only) AC ADAPTOR IR RECEIVER IR-9991 MO NIT OR The figure shows an example for the VR-4090 IR OUT IR IN RF REMOTE ANTENNA S VIDEO VIDEO REC OUT VIDEO1 PLAY IN CD1 DVD REC OUT VIDEO2 PLAY IN VIDEO3 PLAY IN VIDEO4 PLAY IN PLAY IN MONITOR OUT DVD FRONT R AUDIO L SIGNAL GND R AUDIO L PRE OUT FRONT L PHONO R SL 16 TEXT L REC OUT MD/ TAPE1 PLAY IN REC OUT CD2/ TAPE2 MONITOR PLAY IN REC OUT CD-R PLAY IN SYSTEM CONTROL ANTENNA GND AM IR REPEATER OUT DIGITAL OUT IR OUT LCD IR RECEIVER IN REMOTE DC12V 20mA SURROUND SPEAKERS CENTER SPEAKER R LC AC 120V 60Hz SWITCHD TOTAL 90W 0. 75A MAX AC 220240V 30 CD1 R SURROUND CENTER MD/ TAPE1 CD-R SUB WOOFER B R FRONT SPEAKERS L R A L AC 110120V VIDEO2 VIDEO3 SURROUND VIDEO4 OPTICAL COAXIAL DIGITAL IN CENTER SUBWOOFER DVD/6 CH. INPUT IR REPEATER Connections Chapter One : Connecting Your Devices Connecting an External Infrared Receiver and IR Repeaters (VR-4090 and VR-4080 only), continued Your new audio-video receiver supports the IR-9991 twoway external infrared (IR) remote transceiver control. The IR-9991 enables you to use the Receiver's Remote Control unit to operate the receiver if it is: · in a stereo closet/cabinet · behind glass doors · in another room · in any situation where the device to be controlled is not visible You can substitute Xantech (291-80, 480-30, or 490-30 series) IR receivers for the IR-9991. However, these devices are one-way only, and will not supply system status feedback to Remote Control unit. To Connect any other IR Receiver: 1. Connect the IR receiver's output cable to the receiver's IR RECEIVER IN jack. To activate the IR receiver connections, you need to press INPUT MODE key on the front panel of the receiver for more than 2 seconds. · VR-4090/VR-4080 : You will see "RF OFF" on the receiver display. Military : You will see "DATA REAR IN" on the receiver display. To Connect a KENWOOD IR-9991 IR Receiver: 1. Connect the IR-9991's IR IN cable to the receiver's IR RECEIVER IN jack. Connect the IR-9991's IR OUT cable to the receiver's IR OUT LCD REMOTE jack. To activate the IR receiver connections, you need to press INPUT MODE key on the front panel of the receiver for more than 2 seconds. · VR-4090/VR-4080 : You will see "RF OFF" on the receiver display. Military : You will see "DATA REAR IN" on the receiver display. To Connect IR Repeaters: IR repeaters enable you to control components located in cabinets or behind glass doors. Connect the IR repeater to the device as described in the repeater's manual. Connect the IR repeater cable(s) to the Receiver's IR REPEATER OUT jack(s). IR repeaters send a signal similar to the device's own remote control. Xantech repeaters (models 282-00, 286-00, or 283-00) are compatible with your new audio-video receiver. Do not connect IR repeaters unless you have connected an external IR receiver. The connections are only active when an IR receiver is connected. 31 Connections Chapter One : Connecting Your Devices What if I Have Several Kenwood Devices (System Control Chaining)? Connecting system control cords after connecting a KENWOOD audio component system lets you take advantage of convenient system control operations. The system control operation is not available if the unit is connected in the [XS8] connection mode. [. . . ] 34 operating components through external infrared receiver . . . . . . . . . . . . . . . . . . . . . . 37 right speakers front, connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 H hum interference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 I IR repeaters connecting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ]