User manual KENWOOD KRF-X9050D

[. . . ] AUDIO VIDEO SURROUND RECEIVER Preparation Additional Information Remote Control Operations KRF-X9050D INSTRUCTION MANUAL KENWOOD CORPORATION About the supplied remote control Compared to standard remote controls, the remote control supplied with this receiver has several operation modes. These modes enable the remote control to control other audio/video components. In order to effectively use the remote control it is important to read the operating instructions and obtain a proper understanding of the remote control and how to switch its operation modes (etc. ). Using the remote control without completely understanding its design and how to switch the operation modes may result in incorrect operations. B60-4958-00 00 MA (M, Y, T, I, X) 0011 Before applying the power 2 This unit is designed for operation as follows. [. . . ] For more information, refer to the instruction manual of the connected component. For A-REC mode: AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP For M-REC mode: FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED DSP kHz DOWN MIX AUTO FM AUTO SOUND DIGITAL AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP 4 Play the source from the beginning and start recording. · If the audio reproduction stops in the middle due to change in the input signals, etc. , press the DIMMER key. Operations FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP Listening to radio broadcasts 26 The receiver can store up to 40 stations in the memory and recall them by one-touch operation. Radio stations can be classified into RDS (Radio Data System) stations and other stations. To listen to or store RDS stations in the preset memory see "Using RDS (Radio Data System)". only) Presetting radio stations manually The RDS auto memory function assigns preset numbers to RDS stations starting from preset number "1". Therefore, be sure to execute the RDS auto memory function before using the following operations to manually store AM stations and other FM stations, and RDS stations. only) · Tuning radio stations MULTI CONTROL INPUT SELECTOR MULTI CONTROL MEMORY BAND AUTO 1 Tune to the station you want to store. 2 Press the MEMORY key while receiving the station. Blinks for 5 seconds Lights for 5 seconds FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED DSP kHz DOWN MIX TUNING 1/¡ MULTI CONTROL BAND TUNING 1/¡ AUTO TUNER RC-R0714 RC-R0715 BAND AUTO SP A B TI. VOL CLIP MUTE RDS EON PTY TP TA NEWS L LFE C S R SW LS RS Operations TUNER Proceed to step 3 within 5 seconds. (If more than 5 seconds elapse, press the MEMORY key again). 1 Use the INPUT SELECTOR knob (TUNER key) to select the tuner. 3 Use the MULTI CONTROL knob or keys to select one of the station presets (1 ­ 40). 2 Use the BAND key to select the desired broadcast band. Each press switches the band as follows: 1 FM 2 AM FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP 4 Press the MEMORY key again to accept the setting. · Repeat steps 1, 2, 3, and 4 to store as many stations as necessary. · If you store a station at a previously used preset, the old station will be replaced by the new one. "AM" or "FM" indicator appears in the display. Receiving preset stations 3 Use the AUTO key to select the desired tuning method. Each press switches the tuning method as follows: 1 AUTO lit (auto tuning) 2 AUTO not lit (manual tuning) "AUTO" indicator lights up in the display. FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED kHz DOWN MIX DSP Numeric keys TUNER · Normally, set to "AUTO" (auto tuning). If the radio waves are weak and there is a lot of interference, switch to manual tuning. (With manual tuning, stereo broadcasts will be received in monaural. ) RC-R0714 RC-R0715 4 Use the MULTI CONTROL knob or TUNING 1/ ¡ keys to select the station. Frequency display "ST. " lights up when a broadcast is being received in stereo. FM AUTO SOUND DIGITAL AUTO AM PRO LOGIC S. DIRECT MEMO MHz 3 STEREO MONITOR ST. TUNED DSP kHz DOWN MIX 1 Use the TUNER key to select the tuner as the source. 2 Enter the number of the preset you want to receive (up to "40"). Press the numeric keys in the following order: For "15", press . . . . . . . . . . [. . . ] ±10 dB (at 70 Hz) TREBLE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±10 dB (at 10 kHz) Caution : Read this page carefully to ensure safe operation. VIDEO section VIDEO inputs / outputs VIDEO (composite) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 Vp-p / 75 S VIDEO (luminance signal) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0. 286 Vp-p / 75 COMPONENT VIDEO (luminance signal) . . . . . . . . . . . . . . . . . . . . . [. . . ]