User manual KENWOOD KRF-X9995D

[. . . ] i Before Applying Power Read this section carefully to ensure safe operation. KRF-X9995D is designed for operation as follows. AC 230 V only Australia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . AC 110-120/220-240 V switchable *For other countries AC voltage selection The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. [. . . ] 82 To switch on or switch off the RELAY CONTROL output using PowerTouch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82 To switch the video and audio outputs to Zone A or Zone B while Zone A or Zone B is selected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 X-10 Home Automation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83 Lutron . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 iii Makita . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86 Accessories Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88 Chapter Three: Using PowerTouch in Multiple Zones . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Operating Devices in Zone A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93 Operating Devices in Zone B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95 Sound . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97 The 96k fs indicator does not light while a 96k fs compatible disc is being played. 97 I can't hear sound from one or more of the speakers, or the sound is abnormally low. 98 I can hear sound only from the center speaker when Dolby Pro Logic is selected. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98 A Dolby Digital Surround EX-encoded source is played with THX Surround EX set to "Auto", but the source is not reproduced in 6. 1-channel audio. 99 iv Sound from one (or more) of my devices is abnormally loud or soft. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 There wasn't any sound recorded on tapes made on my VCR or tape deck. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 The initial sound is intermittent or non-existent when I start to play from a Dolby Digital, DTS, DTS-ES or MPEG source. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 With a Dolby Digital program or DTS program, the loud sounds aren't very loud and the quiet sounds aren't very quiet. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100 All I hear is loud static when I play DTS discs. [. . . ] · The volume setting (-48dB is selected by default)--see "Adjusting the Volume" on page 11 of this manual. 104 Receiver/Tuner · The tuner's receiving band (FM is selected by default)-- see "Tuner" on page 57 of this manual. · The tuner's frequency (87. 5MHz is selected by default)-- see "Tuner" on page 57 of this manual · The tuner's preset memory--you will need to reset your stored radio stations (see Chapter Two of the Connections and Setup Guide) · The surround setting--see "What are Listen Modes?" on page 18 of this manual. · The speaker settings--you will need to reset your speaker settings ( see Chapter Two of the Connections and Setup Guide) Reset the cleared settings before operating the receiver again. The sound is distorted, and the CLIP indicator on the receiver's front panel flashes red continually, or stays red for more than 1 second at a time. [. . . ]