User manual KONICA MINOLTA 43417990

[. . . ] SYSTEM CONFIGURATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CONTROLLER START-UP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDs and DIP SWITCHES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . LEDs on the Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] 4. 0, 6. 0 Miscellaneous : Should have sufficient memory and resources in the above Windows and other applications used. (2) CPU Apple Macintosh Computers : PowerPC : 16 MB or more : MacOS System7. 5. 3 or later, 8. x and 9. x, OS X (10. 2 or later) Memory OS 1-3. (1) Applicable Browser Specifications Utility Functions · Netscape communicator Ver. 4. 7 or later · Internet Explorer version 5. 0 or later 2. APPEARANCE 4692U001AB M-3 3. COMPONENTLAYOUT NIC Board (Option) 64 MB DIMM (Option) 128 MB DIMM (Option) Main Board HDD (Option) Power Supply Harness 4692M501CB M-4 4. SYSTEM CONFIGURATION · Controller System Configuration PC Windows 95/98/Me/2000/ XP Windows NT4. 0 PCL6 Print Drive PS Print Drive Apple Macintosh PS Print Drive PPD File Ethernet Centronics PJL NIC Board (Netsilicon. Co) PCL5e Emulation PCL6 Emulation PS Core Device Driver Hard Disk Drive (HDD) OS Minolta's Unique Interface Digital Copier Definitions PS Centronics Ethernet PJL : Abbreviation for PostScript, a page description language developed by Adobe Systems, Inc. : Abbreviation for Print Job Language, a system that interprets the language used by the input signal. M-5 5. CONTROLLER START-UP · Turning ON the power switch of the copier with the controller power cable connected to the copier lets the controller perform the start-up procedures. Memory clear (areas required for boot and the dual port RAM for engine I/F) Copies boot loader to RAM. Starts VxWorks. M-6 6. 6-1. LEDs and DIP SWITCHES LEDs on the Main Board · Each of the LEDs on the Main Board turns ON to indicate the following state of the controller. LED0 LED1 LED2 LED3 LED4 4692M502AA LED LED0 LED1 LED2 LED3 LED4 LED5 LED6 LED7 Controller State PDL data being received (parallel, network) Packet being transmitted to the copier Packet being received from the copier Print image data being transmitted to the copier Scan image data being received from the copier Reserved Reserved Reserved M-7 6-2. DIP Switches on the Main Board · DIP switch keys are flipped to the ON and OFF positions to set different states as detailed below when the copier is turned ON. DIPSW2 DIPSW3 DIPSW1 DIPSW4 4692M503AA Purpose Controller diagnostics 1 Controller diagnostics 2 To return controller NVRAM to the factory settings. DIPSW1 DIPSW2 DIPSW3 DIPSW4 OFF OFF OFF ON OFF OFF OFF ON OFF OFF OFF ON NOTE · These are the only permissible combinations of DIP switch key settings. NEVER attempt to make any other combination. M-8 7. 7-1. (1) NIC BOARD (OPTION) Display of LEDs on the NIC Board NIC Board Amber LED 4668M004AC Green LED (2) Normal Operating States Operation Green LED G G Amber LED G G Self-test being carried out when the printer is turned ON. At the end of printer self-test Printer initialization sequence is completed. OFF: , ON: G, Blinking: (3) When an Error Occurs Description A hardware error occurs OFF: , ON: G, Blinking: Green LED Amber LED The green LED flashes OFF and ON once to 12 times, then the amber LED flashes OFF and ON once to 7 times. M-9 7-2. Jumpers on the NIC Board CS1 ON JP2 ON T. B. FACT BYPASS TEST OP7 OP5 OP4 OP3 OP2 OP6 OP1 10/100 BaseT 4668M502CA NOTE · Never change the positions of pins shown in black in the above figures (initial settings). M-10 DIS/REASSEMBLY, ADJUSTMENT 1. 1-1. DISASSEMBLY/REASSEMBLY Remove from the Copier NOTE · Whenever attempting to remove the controller from the copier, be sure to unplug the power cord the copier. 1. NOTE · The type of the screw on the lower right corner is different from the others. 4002U036AA 2. Remove thirteen screws and the exterior cover. 4692U013AB NOTE · Pressing the controller in the direction shown by the arrow, install it so that gasket of the cover is folded inside. Gasket 4692U030AA 4692U028AB 4. Remove four screws, unplug one connector, and remove the controller. 4692D501AA 4692U012AB NOTE · Install the controller according to the procedure. Pressing the controller in the direction shown by the arrow, secure it in position. 4692D502AA 4692D513AA D-3 1-2. Removal and Replacement of a DIMM 1. 8. D-7 TROUBLESHOOTING 1. 1-1. INTRODUCTION General Precautions · When replacing a part or plugging or in unplugging a connector, always make sure that the power cord of the copier has been unplugged. · Never create a closed circuit across connector pins except those specified in the text and on the printed circuit. · When energizing the controller with its cover removed, use utmost care not to touch a board or any other component inside it. · The basic rule is not to run the controller with any of its parts removed. · When the user is using a word processor or personal computer from the power outlet of the same line, take necessary steps to prevent the circuit breaker from opening due to overloads. · Keep all disassembled parts in good order and keep tools under control so that none will be lost or damaged. 1-2. Reading the Text · If a component (except fuses) on a PWB or any other functional unit including the HDD is defective, the text only instructs you to replace the whole PWB or functional unit and does not give troubleshooting procedures applicable within the defective unit. · All troubleshooting procedures contained herein assume that there are no breaks in the harnesses and cords and all connectors are plugged into the right positions. · The text does not contain the removal procedures of covers and parts. · The procedures preclude possible malfunctions due to noise and other network problems. 1-3. Network Problems · Any problem that occurs in conjunction with the operation of the controller over a network should be directed to the network administrator for check and repair. [. . . ] Launch MS-DOS Prompt (for Windows 95/98) or Command Prompt (for Windows NT4. 0/2000) Then enter the following command and press the Enter key. Change current directory to the directory containing the new firmware update file. In this case, type "cd c:\temp" then press "Return Key". The status changes from "18A4", "18A5" to "18A6". [. . . ]