User manual KONICA MINOLTA 7013

[. . . ] RS-232C interface User's Guide Table of contents Setting up . . 8 Setting up After your authorized dealer has installed the RS-232C interface on your machine, follow the steps below to complete your machine's setup. (Your dealer may perform these for you as part of the installation. ) Note: To connect between your fax machine and your computer, you will need an RS-232C interface cable (see next page). [. . . ] 4 for Windows 3. 1 and Ver. 7 for Windows 95 Note: While this RS-232C interface should work with most fax software, there may be some fax packages with which it may not work. If you experience trouble, please confirm that you are following all instructions correctly and in the right order. If you still have trouble, please contact the manufacturer of your fax software package. Note: Before continuing with these instructions, you must first install fax software on your computer. Unimessage, HydraFax and LaserFax are a registered trademarks of Wordcraft Systems, Inc. Bitware is a trademark of Cheyenne Software, Inc. , a division of Computer Associates International, Inc. Windows 3. 1 and Windows 95 are registered trademarks of Microsoft Corporation. 3 Making the RS-232C settings Note: You must make the following settings every time you change your fax software. Note: The parameters for the following settings should be listed in your fax software. If you choose the wrong RS-232C parameters, the fax machine cannot communicate with your computer. The LCD shows the fax's RS-232C transmission speed (baud rate) in bps (bits per second): Baud Rate :Variable / /Enter Note: This setting is just for the RS-232C port. Press or to choose the appropriate baud rate for your computer and software. The settings are: Variable; or 600, 1200, 2400, 4800, 9600 or 19200 bps. Note: If using one of the following our-tested packages, select Variable: ·BitWareTM Ver. Computer: Make sure that your fax software is running and in receive mode. PC-FAX Connection It will take a few moments to initialize the settings. 5 Using your machine's new PC connection Note: While the machine communicates with the computer using the RS-232C interface cable, the machine will not receive the fax message from other fax machine. Scanning from your machine to your computer You can store logos, signatures, line art or even photographs onto your computer by using the fax machine to scan to your computer: 1. PC-FAX Scan A4 Memory 99% Your fax software will now "receive" the fax (including the TTI, if you've set one) onto your computer. To cancel the scanning operation while it's in progress, just press STOP. [. . . ] The fax machine will begin either transmitting or receiving. 7 "AT" commands Note: This is a list of standard "AT" modem commands. For more information, please consult your fax software's instructions. Command A D Parameter none 0 - 9, *, # P T , 0 1 0 1 0 1 2 none none 0 1 none none 1 2 none none none none none none none Description Call answer Dial number Pulse dial Tone dial Pause Not echo command character Echo command character On Hook (Disconnect line) Off Hook (Connect line) Monitor speaker is always off Monitor speaker is on until carrier is detected Monitor speaker is always on Set pulse dial mode Set tone dial mode Short formed response code Long formed response code Reset modem Initialize to factory setting XON/XOFF flow control RS/CS flow control Indicate current service class Indicate service class capability Set service class Receive HDLC frame (n=3:300 bps) XON/XOFF flow control (n=1) RS/CS flow control (n=2) Facsimile receive message (14400/12000/9600/7200/4800/ 2400 bps) Detect silence for n x 10ms Transmit HDLC frame (n=3:300 bps) Facsimile transmit message (14400/12000/9600/7200/4800/ 2400bps) Wait for n x 10ms Default value E H M E0 M1 P T V Z &F \Q +FCLASS?+FCLASS=n +FRH=n +FLO=n +FRM=n V1 \Q2 +FLO=2 +FRS=n +FTH=n +FTM=n none none none +FTS=n none 8 D88-90360-60 [. . . ]