User manual KONICA MINOLTA 7040

[. . . ] INSTRUCTION MANUAL 7040 INSTRUCTION MANUAL 7040 Before copying, read this guide. Keep in the right hand rear pocket of the machine. Thank you very much for your purchase of the Konica 7040. This Manual deals with making copies, correct handling of the machine, and precautions for safety. In order to maintain a satisfactory copying performance, please keep this Manual readily available for reference in the right hand rear pocket of the machine. ENERGY STAR® Program The ENERGY STAR Program has been established to encourage the widespread and voluntary use of energy-efficient technologies that reduce energy consumption and prevent pollution. [. . . ] Advice To return to the initial condition, touch "CANCEL" key. When copying more than 50 originals, use RADF store mode or Platen store mode. Advice To clear all application settings, touch "ALL CLEAR" key. To copy in different magnification ratio, display the Lens Mode screen to select the desired magnification. Basic screen Lens Mode screen x Enter Print Quantity The print quantity is always set as 1. Put originals in the order of pagination, and place them FACE UP in the RADF. 6-8. OHP Interleave Supplement 1: Using Store mode RADF store mode: To copy a set of more than 50 originals, use RADF store mode. Touch and highlight the "Store Mode" key on the Application Selection screen. Divide the originals into blocks not exceeding 50 sheets and load them from the block with the first page. Platen store mode: To copy originals that cannot be fed through the RADF onto both sides of copy paper, use Platen store mode. Touch and highlight the "Store Mode" key on the Application Selection screen. 7-7 for details. 8 - 31 Section 8 : Special Copying : Page Editing 6. OHP Interleave (continued) Supplement 2: Checking copying conditions/printed copies 1. Touch "PROOF COPY" key on the Check screen to make a proof copy. When completed, touch "EXIT" key to return to the Basic screen. Originals loaded on RADF are all scanned and discharged, then output job starts in succession. ERROR POWER SAVER ON / OFF 2 When using Store mode, press the START PRINT button to start the output job. 5 3 6 INTERRUPT To stop copying, press the STOP/CLEAR button. After completion of copying, all the data in the memory will 0 be cleared. STOP / CLEAR 9 CLEAR QTY. 12-5. CAUTION: Paper Capacity of the Finisher The capacity of the Finisher exit tray is listed below. When the total number of copies in the copy run exceeds the stated capacity, be sure to unload the exit tray whilst the copier is still copying. When copying mixed size originals, the capacity will be less than the following. Non-sort mode Tray 1: 100 sheets/ 10 sheets (thin/thick paper, OHP films, etc. ) Tray 2/3: 500 sheets (A4R, A4, B5R, B5, 8. 5"x11"R) 300 sheets (A3, B4, F4/8. 5"x13", A5R) Sort/Group mode Tray 2/3: 500 sheets (A4R, A4, B5R, B5, 8. 5"x11"R) 300 sheets (A3, B4, F4/8. 5"x13") CAUTION: Maximum Loading Capacity of the Exit Tray In the case of the copier without a finisher, the exit tray capacity is 100 sheets. Be sure to remove the copies from the exit tray while copying before the maximum capacity is reached. [. . . ] 6-24~6-27. ) If further adjustment required, contact your service centre. 6-24~6-27. ) If further adjustment required, contact your service centre. · Call your service centre. Main Body Copy image is too light. Is density adjustment correct?Is the "Call for PM" message displayed? Is Repeat, Image Shift, Reduce · Cancel Repeat, the Image Shift, Reduce & Shift or Dual Page & Shift or Dual Page mode mode. [. . . ]