User manual KONICA MINOLTA BIZHUB C250

[. . . ] 750/600 Facsimile operations Table of contents Table of contents 1 Introduction 1. 1 1. 1. 1 1. 1. 2 1. 1. 3 1. 1. 4 1. 2 1. 3 1. 4 1. 5 1. 5. 1 1. 5. 2 1. 6 Special Notice to User . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 For Canada . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 For New Zealand . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] ­ See "Setting Transmission Conditions" on page 3-10 for information about setting functions in the FAX screen. See "Application Functions Overview" on page 7-4 for information about setting functions in the FAX Application screen. 7-38 bizhub 750/600 Transmission Applications 7 Chapter 7 7-39 8 Designate the relay station. ­ See "Selecting One Destination" on page 3-19 for information about designating the destination. ­ See "Placing Originals on the Platen Glass" on page 3-6 for information about setting the document. 10 Press [Start]. The FK-502 stores the document in memory before starting transmission. ! Detail To interrupt the operating sequence, press [Stop]. bizhub 750/600 Transmission Applications 9 Set the original document. 7 Chapter 7 Transmission Applications 7. 15 ECM OFF ECM OFF Transmission can be made with ECM disabled. Error Correction Mode (ECM) is a mode of transmission with error correction established by ITU-T (International Telecommunications Union). FAX machines equipped with the ECM feature can communicate with each other and can confirm that the data sent is free of errors. Thus, communication can be made free from disturbances due to line noises, etc. 0 Specifications If there are many line disturbances, the communication time may be a little bit longer with ECM enabled than with ECM disabled. 0 Functions incompatible Polling RX (Normal), Polling TX (Normal), V. 34 OFF, Bulletin Board Registration, Polling RX (Bulletin) Transmission Applications 1 2 3 Press [Fax] on the control panel to view the FAX screen, if it is not already displayed. Press [Line Setting]. 7-40 bizhub 750/600 Transmission Applications 7 Chapter 7 7-41 4 Press [ECM OFF]. ­ To release the setting, press [ECM OFF] again. 5 6 7 Press [OK]. ­ See "Setting Transmission Conditions" on page 3-10 for information about setting functions in the FAX screen. See "Application Functions Overview" on page 7-4 for information about setting functions in the Fax Application Menu. 8 Designate the destination. ­ See "Selecting One Destination" on page 3-19 for designating the destination. 9 Set the original document. ­ See "Placing Originals on the Platen Glass" on page 3-6 for information about setting the document. 10 Press [Start]. The FK-502 starts transmission. ! Detail To cancel transmission, see "Canceling Transmission" on page 3-32. If the destination is not ready to receive, your call will be redialed. For information about redialing, see "Manual Redialing" on page 3-27. If transmission fails, refer to "Cannot Send Messages" on page 5-2. bizhub 750/600 Transmission Applications 7 Chapter 7 Transmission Applications 7. 16 V. 34 OFF V. 34 OFF V. 34 is a communication mode used by the Super G3 FAX. When a destination or the FK-502 is connected to a line by way of extension exchange equipment, you may not be able to communicate with the super G3 depending on line conditions. In such a case, we recommend that you transmit by selecting V. 34 OFF to set the super G3 mode off. The V. 34 mode will be resumed automatically on completion of transmission. 0 Functions incompatible Polling TX (Normal), Polling RX (Normal), Bulletin Board Registration, Polling RX (Bulletin), ECM OFF Transmission Applications 1 2 3 Press [Fax] on the control panel to view the FAX screen, if it is not already displayed. [. . . ] The function to reserve the next transmission during communication or printing. The documents are stored in memory, and you can send again either to the same destination or after changing to a different destination. Pause Polling Program Q Quick memory transmission R Reading Redialing Relay TX Relaying station Reserving transmission Resolution Restored Transmission bizhub 750/600 13-9 Appendix Chapter 13 13 Chapter 13 Terms Description Appendix S Sender information Sender name Information such as transmission date, name, telephone number, and page number printed at the top of the received document at the fax transmission. The name of this machine, which is represented with any alphanumeric character and symbols. It is recorded as the part of the originating printing at the top of the received document on the receiver side. [. . . ]