User manual KONICA MINOLTA BIZHUB PRO 1050E

[. . . ] 1050/1050e Operator Manual · Copier · POD Administrator · Security Table of Contents 1 Safety Information 1. 1 1. 1. 1 1. 1. 2 1. 2 1. 2. 1 1. 2. 2 1. 2. 3 1. 2. 4 1. 2. 5 1. 3 1. 4 Safety Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Warning and Precaution Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Meaning of Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3 Regulation Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Touch [Return] to restore the Multi Folder (Fold) Adjustment Mode Menu Screen. bizhub PRO 1050/1050e 13-49 13 06 Gate Position Adjustment Adjustment Perform this adjustment for the folding positions in Gate folding mode processed by the Folding Unit FD-501. 2 Reminder When adjusting Single Fold, Double Fold and Triple Fold at a time, be sure to start with the Single Fold adjustment. The baseline of Single Fold is calculated from the edge of the sheet, while that of Double Fold is calculated from the position of the first fold line, and that of Triple Fold is calculated from the position of the second fold line, therefore a distance (a), distance (b) and distance (c) in step 5 will be altered by changing the position of any fold position. 13-50 bizhub PRO 1050/1050e Adjustment 13 Procedure 1 2 3 4 5 Touch [Adjustment ]- [02 Finisher Adjustment] - [03 Multi Folder (Fold) Adj. ]. Touch [06 Gate Position Adjustment] to display the Gate Position Adjustment Screen. Load the desired size of paper to be adjusted on a tray, specify [Gate], then press [Start]. Check a distance (a), distance (b) and distance (c) on the output sheet. 1 a 3 2 b c Paper feed direction 6 If the desired result cannot be obtained, touch the [ADJUSTMENT] tab. bizhub PRO 1050/1050e 13-51 13 7 Adjustment Touch [Next] or [Back] to select the paper size to be adjusted. Touching [Next] continuously will change the paper size as follows: All - 11x17 - A3 - B4 - 8. 5x14 - A4R - 8. 5x11R - 8K - 12x18 8 9 Touch [Single Fold]. Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -50 to +50, 1 step = 0. 1 mm 2 Note The distance (a) in step 5 will decrease when the "+" value is entered, and increase when the "-" value is entered. 10 Touch [Double Fold] and [Triple Fold] to set in the same manner respectively. 2 Note In Double Fold, the distance (b) in step 5 will increase when the "+" value is entered, and decrease when the "-" value is entered. In Triple Fold, the distance (c) in step 5 will decrease when the "+" value is entered, and increase when the "-" value is entered. 11 12 Repeat steps 3 to 10 until the desired result is obtained. Touch [Return] to restore the Multi Folder (Fold) Adjustment Mode Menu Screen. 13-52 bizhub PRO 1050/1050e Adjustment 13 13. 9 04 Stacker Adjustment 01 Paper Width Adjustment Perform this adjustment when output sheets are not aligned in a perpendicular position to the direction of paper feed processed by the Large Capacity Stacker LS-501/502. bizhub PRO 1050/1050e 13-53 13 Procedure Adjustment 1 2 3 4 5 6 7 Touch [Adjustment] - [02 Finisher Adjustment] - [04 Stacker Adj. ]. Touch [01 Paper Width Adjustment] to display the Paper Width Adjustment Screen. Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -20 (narrow) to +20 (wide), 1 step = 0. 1 mm 8 9 10 If the desired result cannot be obtained, touch the [ADJUSTMENT] tab. Touch [Return] to restore the Stacker Adjustment Mode Menu Screen. 13-54 bizhub PRO 1050/1050e Adjustment 02 Paper Length Adjustment 13 Perform this adjustment when output sheets are not aligned to the direction of paper feed processed by the Large Capacity Stacker LS-501/502. bizhub PRO 1050/1050e 13-55 13 Procedure Adjustment 1 2 3 4 5 6 7 Touch [Adjustment] - [02 Finisher Adjustment] - [04 Stacker Adj. ]. Touch [02 Paper Length Adjustment] to display the Paper Length Adjustment Screen. Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -20 (narrow) to +20 (wide), 1 step = 0. 1 mm 8 9 10 If the desired result cannot be obtained, touch the [ADJUSTMENT] tab. Touch [Return] to restore the Stacker Adjustment Mode Menu Screen. 13-56 bizhub PRO 1050/1050e Adjustment 13 13. 10 05 Saddle Stitcher Adjustment 01 Stapling Centre Adjustment Perform this adjustment for the centre (folding) position of copied/printed sheets and of staples processed by the Saddle Stitcher SD-501. The paper width adjustment (06) and folding position adjustment (04) are supposed to be completed before this adjustment. bizhub PRO 1050/1050e 13-57 13 Adjustment Procedure 1 2 3 4 5 Touch [Adjustment] - [02 Finisher Adjustment] - [05 Saddle Stitcher Adj. ]. Touch [01 Stapling Centre Adjustment] to display the Stapling Centre Position Adjustment Screen. Check misalignment (a) of the folded line and stapling position. [1] a [2] 6 If the test desired result cannot be obtained, touch the [ADJUSTMENT] tab. 13-58 bizhub PRO 1050/1050e Adjustment 13 Use the touch panel keypad to enter the desired adjustment value, then touch [Set]. Available range: -20 (forward) to +20 (backward), 1 step = 0. 1 mm 7 8 9 Repeat the adjustment steps from 3 to 7 until the desired result is obtained. [. . . ] 5-4 Punch mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-28 23 Resolution . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-57 Saddle Stitcher SD-501 2-13, 22-9 Saddle stitcher tray . . . . . . . . . . . . . . . 17-51 Section management setting 17-54 Section name input . . . . . . . . . . . . . 14-17 Select tray when APS cancel 16-46 Selecting an output tray . . . . . . . . . . [. . . ]