User manual KONICA MINOLTA BIZHUB-350-250 PH2-5 UM COPY 1-1-0

[. . . ] 350/250 Copy operations Contents 1 Introduction 1. 1 1. 2 Energy Star®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Trademarks and registered trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 License information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 OpenSSL Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The Zoom screen appears again. ! Detail The enter zoom ratio can be stored. For details on storing zoom ratios, refer to "Storing the desired zoom ratio" on page 4-38. 4-34 bizhub 350/250 (Phase 2. 5) Basic copy operation Specifying separate horizontal and vertical zoom ratios (Individual Zoom settings) 4 By using the keypad, separate zoom ratios can be typed in directly for the horizontal direction (between e0. 250 and e4. 000) and for the vertical direction (between e0. 250 and e4. 000). By changing the horizontal and vertical zoom ratios, the copy image can be resized as shown in the following illustration. 1 In the Basics screen, touch [Zoom]. The XY Zoom screen appears. bizhub 350/250 (Phase 2. 5) 4-35 4 3 Touch [Individual Zoom]. The Individual Zoom screen appears. Basic copy operation 4 Using the keypad, type in the desired zoom ratios for side X and side Y (between e0. 250 and e4. 000). ­ If a value outside the allowable range is specified, the message "Input Error" appears. If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. ­ 5 Touch [Enter]. The Zoom screen appears again. 4-36 bizhub 350/250 (Phase 2. 5) Basic copy operation Selecting a stored zoom ratio 4 Copy zoom ratios that have been stored can be recalled to be used when desired. For details on storing zoom ratios, refer to "Storing the desired zoom ratio" on page 4-38. 0 The zoom ratios e1. 000, e1. 000 and e0. 930 have been stored. 1 In the Basics screen, touch [Zoom]. The XY Zoom screen appears. 3 Touch the button for the desired zoom ratio. 4 Touch [Enter]. The Zoom screen appears again. bizhub 350/250 (Phase 2. 5) 4-37 4 Storing the desired zoom ratio Basic copy operation Two frequently used zoom ratios and the zoom ratio for the "Minimal" setting can be stored. When a new zoom ratio is stored, it overwrites the zoom ratio stored with the selected button. 1 In the Basics screen, touch [Zoom]. The Set Zoom screen appears. 4-38 bizhub 350/250 (Phase 2. 5) Basic copy operation 4 4 Using the keypad, type in the desired zoom ratio (between e0. 250 and e4. 000). ­ If a value outside the allowable range is specified, the message "Input Error" appears. If the value was incorrectly entered, press the [C] (clear) key in the keypad to erase the value, and then specify the correct value. To store a "Minimal" zoom ratio, type in the desired zoom ratio between e0. 900 and e0. 999. ­ ­ 5 Touch the button or [Minimal] where the new zoom ratio is to be stored. 6 Touch [Enter]. The XY Zoom screen appears again. bizhub 350/250 (Phase 2. 5) 4-39 4 4. 7 Basic copy operation Selecting single-/double-sided settings for originals and copies The following four combinations of the "Single-Sided" and "Double-Sided" settings are available originals and copies. Original/copy settings Single-Sided % Single-Sided Description Select this setting to produce single-sided copies from single-sided documents. Single-Sided % Double-Sided Select this setting to produce one double-sided copy from two single-sided documents. Double-Sided % Single-Sided Select this setting to produce two single-sided copies from one double-sided document. Double-Sided % Double-Sided Select this setting to produce double-sided copies from double-sided documents. 4-40 bizhub 350/250 (Phase 2. 5) Basic copy operation To select single-sided copies 4 0 As a factory default, the "Single-Sided" Original setting and the "SingleSided" Copy setting are selected. 0 If the "Double-Sided" Original setting and the "Single-Sided" Copy setting are selected, specify the position of the binding margin and the loading orientation for the document, otherwise the copies will not be printed as desired. For details on specifying the position of the binding margin, refer to "Selecting the position of the binding margin (Margin settings)" on page 4-22. For details on specifying the document orientation, refer to "Selecting the document orientation (Original Direction settings)" on page 4-20. 0 For details on using the original glass to scan multiple document pages, refer to "Scanning a multi-page document from the original glass" on page 4-15. 1 In the Basics screen, touch [Simplex/Duplex]. [. . . ] Set this function to later scan multiple images from the original glass and insert them at the desired locations in a document scanned with the ADF, then feed out all copies together. Set this function to insert paper from the specified paper tray into the copies as chapter title pages. The copy operation that is queued on the machine while copying; Multiple jobs can be queued on the machine. Optional paper feed cabinet that can be loaded with up to 2, 500 sheets of paper. [. . . ]