User manual KONICA MINOLTA BIZHUB-750-600 PH2 UM COPY 1-1-0

[. . . ] 750/600 User Manual Contents 1 Introduction 1. 1 1. 2 1. 3 Energy Star®. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 Trademarks and registered trademarks. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 Available features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6 Automatically selecting the paper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] For details on the Enlarge Display mode, refer to the User manual [Enlarge Display Operations]. If the time setting is the same for the automatic panel reset operation and the automatic system reset operation, the display of the message requesting confirmation to cancel Enlarge Display mode is given priority and the message requesting confirmation to reset the settings in Enlarge Display mode is not displayed. bizhub 750/600 (Phase 2) 5-47 5 Additional copy operations To set the "Enlarge Display Confirmation Screen" function When the [Enlarge Display] key is pressed to change the display of the screen, a message can be displayed, requesting confirmation to reset the settings to their defaults. The factory default setting is "No". 5-48 bizhub 750/600 (Phase 2) Additional copy operations 5 1 2 Display the Accessibility Setting screen. (To display the screen, refer to page 5-27) Touch [Enlarge Display Confirmation Screen] or press the [7] key in the keypad. The Enlarge Display Confirmation Screen screen appears. 3 Select whether or not the message is displayed. ­ To cancel changes to the settings, touch [Cancel]. bizhub 750/600 (Phase 2) 5-49 5 4 5 Touch [OK]. Additional copy operations The Accessibility Setting screen appears again. The Basic screen appears again. 2 Note The Enlarge Display mode is compatible with basic copy, scanning and fax functions. With the Enlarge Display mode, text and illustrations are displayed at a larger size so that they can be seen more easily. For details on the Enlarge Display mode, refer to the User manual [Enlarge Display Operations]. If [No] is touched in the message requesting confirmation to enter Enlarge Display mode, the screens are not changed. 5-50 bizhub 750/600 (Phase 2) 6 Troubleshooting Troubleshooting 6 6 6. 1 Troubleshooting When the message "Malfunction detected. " appears (Call Technical Representative) If a malfunction that cannot be corrected by the user occurred, the message "Malfunction detected. (call technical representative screen) The phone number and fax number for the usual technical representative appears in the center of the call technical representative screen. Display in Enlarge Display mode If a malfunction occurs, the screen shown below appears. bizhub 750/600 (Phase 2) 6-3 6 Touch Troubleshooting to display the message shown in the following illustration. 6-4 bizhub 750/600 (Phase 2) Troubleshooting To call the technical representative 6 1 2 Write down the malfunction code (for example, C-0001) in the call technical representative screen. Turn off the sub power switch. 3 Use the main power switch to turn off the machine. 4 5 Unplug the machine. Contact the technical representative, and inform them of the malfunction code. 2 Reminder Since the machine may be damaged, contact the technical representative according to the procedure described above as soon as the call technical representative screen appears. bizhub 750/600 (Phase 2) 6-5 6 2 Note Troubleshooting If CS Remote Care is being operated from the Service Center, the Service Center is automatically notified of the malfunction code. CS Remote Care has called the Service Center. " appears, turn off the sub power switch and the main power switch, and then unplug the machine from the electrical outlet. 6-6 bizhub 750/600 (Phase 2) Troubleshooting 6 6. 2 When the message "Misfeed detected. " appears If a misfeed occurs during copying or printing, the message "Misfeed detected. " appears and the location of the misfeed is indicated in the screen. (misfeed screen) At this time, copying and printing cannot continue until the misfeed is adequately cleared. If paper misfeeds have occurred at multiple locations, multiple "o" and arrows appear or flash. The flashing "o" and arrow indicate locations where the paper misfeed should be cleared first. Clear the paper misfeeds according to the messages that appear in the guidance display area. Illustration button Touch this button to display a screen that contains illustrations describing the recommended procedure for clearing the paper misfeed. Illustration description area "o" indicates the location of the paper misfeed, and the arrow indicates the operation for clearing the misfeed. Guidance display area Displays the basic procedures for clearing paper misfeeds. 2 Note The illustration above shows all "o" and arrows displayed; however, normally, all marks will not appear. Error codes may appear in the illustration description area of the JAM location display screen. For details, contact your technical representative. bizhub 750/600 (Phase 2) 6-7 6 To clear a paper misfeed Troubleshooting 1 In the JAM location display screen, touch [Illustration]. If the description of the illustration extends over multiple pages, [Next ] appears in the lower-right corner of the screen. ­ To return to the previous illustration description screen, touch [ Back]. The illustration screen appears. ­ Touch [JAM location display] to return to the JAM location display screen. 2 Clear the paper misfeed according to the instructions that appear in the screen. ­ ­ When removing misfeed paper, be careful that the paper does not tear and remain in the machine. Do not touch or scratch the surface of the drum. 6-8 bizhub 750/600 (Phase 2) Troubleshooting 6 3 After the procedure is finished, the Basic screen appears again. [. . . ] The setting specified first is given priority, and a warning message appears. · When an optional paper tray is selected for "Front Cover Paper" or "Back Cover Paper" of the "Cover Mode" function · When combined with the "Insert Sheet" function · When a Combine Originals setting is selected · When the "Booklet" function is specified · When the "Image Repeat" function is specified The "Mixed Original" setting and "Group" setting can be combined; however, they cannot be combined if a Staple setting is also selected. 14-14 bizhub 750/600 (Phase 2) Appendix 14 Function combination code keys If the cover sheet is thick paper and the paper for the body text is plain paper while using the "Cover Mode" function, a Staple setting can also be selected. In any other case, the settings cannot be combined, the setting specified first is given priority, and a warning message appears. Automatically selected when settings for the "Book Copy" function are selected. [. . . ]