User manual KONICA MINOLTA BIZHUB-750-600 PH2 UM SCAN 1-1-0

[. . . ] 750/600 User's Guide [Network Scanner Operations] Contents 1 Introduction 1. 1 Trademarks and Registered Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 License information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4 OpenSSL Statement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5 About This Manual. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Use the keypad to type in the address. TCP/IP Setting screen 4/5 Item DNS Domain Auto Obtain DNS Default Domain Name Description Select whether to automatically acquire the DNS domain name. Use the keyboard that appears in the touch panel to type in the name (up to 253 characters). Use the keyboard that appears in the touch panel to type in the name (up to 253 characters). DNS Search Domain Name1-3 bizhub 750/600 (Phase 2) 4-57 4 TCP/IP Setting screen 5/5 Item DynamicDNS Setting Host Name IP Filtering RAW Port No. Specifying Settings From the Control Panel Description If the DNS server being used supports the dynamic DNS function, specify whether to enable a dynamic DNS. Use the keyboard on the control panel to type in the host name of this machine. For details on specifying the setting, refer to "IP Filtering" on page 4-63. For details on specifying the setting, refer to "RAW Port No. " on page 4-65. 2 Note Be sure to enter the host name and domain name so that the total number of characters entered is within 254 characters. 4-58 bizhub 750/600 (Phase 2) Specifying Settings From the Control Panel To specify TCP/IP settings 4 1 2 3 In the Administrator Setting screen, touch [5 Network Setting]. (Refer to "To display the Administrator Setting screen" on page 4-10 for more details. ) In the Network Setting screen, touch [2 TCP/IP Setting]. TCP/IP Setting screen 2/5 appears. bizhub 750/600 (Phase 2) 4-59 4 5 ­ Specifying Settings From the Control Panel Specify the desired settings. If [Auto Input] was selected under "IP Address Setting Method", specify the automatic acquisition procedure, and then touch [OK]. 6 7 Touch [Fwd. ]. Specify the desired settings. 4-60 bizhub 750/600 (Phase 2) Specifying Settings From the Control Panel 4 8 9 Touch [Fwd. ]. The TCP/IP settings are applied. bizhub 750/600 (Phase 2) 4-61 4 2 Note Specifying Settings From the Control Panel To cancel changes to the setting, touch [Cancel]. To quit specifying the Utility mode setting, touch [Exit] in the sub display area or press the [Utility/Counter] key. Otherwise, cancel the Utility mode by touching [Close] in each screen until the screen for the Copy, Fax, Scan or Box mode appears. 2 Reminder In order to apply the changes made to [TCP/IP Setting] and [IP Address Setting Method], the machine must be turned off, then on again. 4-62 bizhub 750/600 (Phase 2) Specifying Settings From the Control Panel IP Filtering The IP addresses in the specified ranges can be permitted or denied. 4 IP addresses can connect depending on whether "Enable" or "Disable" has been selected for "Permit Access" and "Deny Access" in the IP Filtering screen, as shown below. Setting Permit Access Disable Deny Access Disable Permit Access Enable Deny Access Disable Permit Access Disable Deny Access Enable Permit Access Enable Deny Access Enable IP Address All IP addresses Connection Access Connection possible IP addresses in the specified range IP addresses out of the specified range Connection possible Connection not possible IP addresses in the specified range IP addresses out of the specified range Connection not possible Connection possible IP address in the range allowed access and out of the range denied access IP address in the range allowed access and in the range denied access IP address out of the range allowed access and out of the range denied access IP address out of the range allowed access and in the range denied access Connection possible Connection not possible Connection not possible Connection not possible 1 2 In TCP/IP Setting screen 5/5, touch [IP Filtering]. Touch [Enable] or [Disable] under "Permit Access". bizhub 750/600 (Phase 2) 4-63 4 3 Specifying Settings From the Control Panel Touch the button for a set (Set 1 to Set 5), and then use the keypad to type in the address range. For example, to specify all addresses before 192. 168. 1. 20, specify the range from 0. 0. 0. 1 to 192. 168. 1. 20. The procedure for setting the IP addresses is the same as on the Permit Access screen. To edit the values that you entered, touch [ ] or [ ] to move the cursor to the desired area, touch [Delete], and enter the new value. To clear all values, press the [C] (clear) key. ­ ­ ­ 4 Touch [OK]. IP filtering is set. 2 Note To cancel changes to the setting, touch [Cancel]. 4-64 bizhub 750/600 (Phase 2) Specifying Settings From the Control Panel RAW Port No. 4 Specify the RAW port numbers used by the printer. By specifying multiple port numbers, multiple data can be accepted simultaneously. 1 2 In TCP/IP Setting screen 5/5, touch [RAW Port No. ]. To use the selected port, press the [C] (clear) key to erase the value, and then use the keypad to type in the RAW port number (between 1 and 65535). ­ If a value outside of the allowable range is specified, the message "Input Error" appears. [. . . ] Specify whether or not the multifunctional product searches this specified LDAP server. Displays the ability to reproduce the details of images and print matter correctly. A function that allows you to view an image before processing a print or scan job. When using a printer driver, various functions can be specified in the file properties. [. . . ]