User manual KONICA MINOLTA EP1031F

[. . . ] This declaration is valid for the area of the European Union (EU) only. Product Type Product Name Options Standards Copying Machine EP1031F MB-4 Safety : EN 60 950 / 1992 (Safety of information technology equipment, including electrical business equipment) EMC : EN 55 022 (Class B) / 1995 (Limits and method for measurement of radio disturbance characteristics of information technology equipment (ITE)) EN 55 082-1 / 1992 (Electromagnetic compatibility - Generic immunity standard Part1: Residential, commercial and light industry) EC 801-2 / 1991 (Electrostatic discharge requirement) IEC 801-3 / 1984 and IEC 801-3 / 1992 (draft) (Radiated electromagnetic field requirement) IEC 801-4 / 1988 (Electrical fast transient / burst requirement) Safety : 73 / 23 / EEC and 93 / 68 / EEC art. 5 EC Directives ii Contents Chapters 1 through 3 give the basic information for making copies. Be sure to read these chapters before using your copier. Using this Manual Organization viii Page Organization ix Terms and Symbols for the Type of Originals and Copy Paper x Chapter 1 Safety Notes 1. 4 Operating Environment Using the Copier Properly Care of Copier Supplies Moving iii Contents Chapter 2 Getting to Know your Copier 1. [. . . ] If the book is thick, you can make copies with the Original Cover raised. * "Book original" refers to an open bound original. NOTES · Not positioning an open book properly will result in copies with pages in incorrect order. · Do not look directly at the Original Glass surface, as a very intense beam of light can be emitted. Book 2 1158O017CA Press the Book Key. · The Book Indicator lights up. 1158O017CA 37 2. Copying Procedure NOTE · If paper other than A4 crosswise A3 A4 A4 A5 Paper @ @ @ @ @ @ @ @ paper is loaded into the Drawer when the Book Copying Mode is selected, the Drawer Indicator and the corresponding Paper Size Indicator blink on the Control Panel. In such a case, load paper of the same size and in the same direction of each page of a book into the Drawer. 1158O026DA 1158O026DA 1139O1460A A4 Crosswise Making Copies Chapter 3 38 2. Copying Procedure Number of Copies 1 Meter Count Toner Drum Dehumidify 2 5 8 0 3 6 9 C Paper A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 100% 4 7 Book Auto Photo Lighter Darker Auto/Photo A 1158O027DA Chapter 3 Setting the Number of Copies 1 2 5 8 0 3 6 9 C 1142O171AA Using the Key Pad, enter the number of copies to be made. * The maximum number that can be Making Copies 4 7 set is 99. Example: To make 18 copies, press Key and then Key , in that order. The Multi-Copy Display now shows "18. " 1139O3740A Correcting the Number Entry 1 4 7 2 5 8 0 3 6 9 C 1142O169AA To correct or reset a number entry, press the Clear Key. * The Multi-Copy Display is reset to "1. " 1139O3750A 39 2. Copying Procedure Starting the Copy Cycle 1 Meter Count Toner Drum Dehumidify 2 5 8 0 3 6 9 C Paper A3 A4 A4 A5 @ @ @ @ @ @ B4 @ FLS. @ Inch % 50%~200% 141% A4 @ A3 115% B4 @ A3 100% @ @ @Full Size 81% B4 @ A4 70% A3 @ A4 100% 4 7 Book Auto Photo Lighter Darker Auto/Photo A Starting the Copy Cycle 2 1139O2360A Press the Start Key, if it is green. The Start Key turns orange when the copy cycle starts. Stopping a Multi-Copy Cycle Stop To stop a multi-copy cycle in progress, press the Stop Key. In such a case, you can use the Toner Replenisher function to regain the normal image density quickly. Meter Count Toner Drum Dehumidify 1142O152CA 1142O152CA Original Copy Copy Made After Toner Replenishing Auxiliary Functions Chapter 4 1142O148CB Even if you continue making copies after the image density has become lighter, the copier will gradually recover the normal image density. The Toner Replenisher Mode can, however, be used to obtain the normal image density more quickly. Meter Count Toner Drum Dehumidify 1142O118CA 1142O118CA Press the Auxiliary Toner Replenishing Key. This causes the copier to initiate toner replenishing, which lasts for 90 seconds at maximum. NOTE · Do not turn the Power Switch OFF or open the Front or Right Door while the copier is replenishing toner. 47 3. Drum Dehumidifier Function During high humidity periods or when there are sudden rapid changes in humidity (especially when you are using a heater in winter), condensation*1 could form on the surface of the PC Drum*2, resulting in blotchy copies. In such instances, use the Drum Dehumidify Key to dry the surface of the PC Drum. 1142O152CA 1142O152CA Before a Drum Dehumidifier Operation After a Drum Dehumidifier Operation Meter Count Toner Drum Dehumidify Meter Count Toner Drum Dehumidify 1142O119CA 1 2 1142O119CA Press the Drum Dehumidify Key. This sets the copier into the Drum Dehumidifier Mode which lasts for 90 seconds. Run the Drum Dehumidifier cycle once again if the copy image is not yet clear. Useful Tip A copy cycle can be initiated even while the copier is in the Drum Dehumidifier Mode. NOTE The copier cannot be set into the Drum Dehumidifier Mode while it is warming up. *1: Condensation: A phenomenon in which small drops of water are formed on cold surfaces, such as the surface of the PC Drum. *2: PC Drum: Functions in the copier as film does in a camera. Auxiliary Functions 1142O149CB Chapter 4 48 4. User's Choice The copier has been set so that the most frequently used settings are automatically selected in the initial mode. [. . . ] Is any of the following Indicators lit up? 1139O3910A 1139O3270A 1139O3930A 1139O3940A The Copier is not activated when the Power Switch is turned ON. Is the power cord plugged into the power outlet?Is the room circuit breaker open? Turn the copier OFF immediately, unplug the power cord, and call your Technical Representative. Troubleshooting Chapter 6 87 2. The Copier is not Functioning as Designed Action The copier is in the Energy Saver Mode. Close the room circuit breaker. Troubleshooting Chapter 6 88 2. [. . . ]