User manual KONICA MINOLTA EP1050

[. . . ] This operator's manual explains how to operate the copier and replenish its supplies. It also gives some troubleshooting tips as well as general precautions to be observed when operating the copier. To ensure the best performance and effective use of your copier, read this manual carefully until you familiarize yourself thoroughly with its operation and features. Please use this manual as a quick and handy reference tool for immediately clarifying any questions which may arise. ii Contents Chapters 1 through 3 give the basic information for making copies. [. . . ] Auto Dual Function in the Sort Mode When 5 or less copies are made from an original set consisting of more than 25 originals in the Sort Mode, the Sorter is automatically switched into the Auto Dual Function Mode using the 6th to 10th Bins. Chapter 3 Copies 1st to 25th sorted copies 26th to 50th sorted copies Top to 5th Bins 6th to 10th Bins Bins used Making Copies * If the number of copies selected exceeds 5, the new copy cycle stops at the 25th original. Example: Making 3 copy sets of a 30-page original set Sorter · Top three Bins contain 25 sorted copies. 30-Page Original Set Sorting into 3 Sets 1139O1140A * To have a complete set from the originals, place the copies from the 6th Bin on top of those from the Top Bin. In the same way, place copies from the 7th Bin on top of those from the 2nd Bin, and so on. 47 2. Copying Procedure Number of Copies 1 Meter Count Toner Drum Dehumidify 2 5 8 0 Start 3 6 9 C Stop Panel Reset Energy Saver % Paper 4 7 A4 Auto 50%~200% 141% 115% 100% 81% 70% A4 A3 B4 A3 Full Size B4 A4 A3 A4 100% Auto Size Sort Book Lighter A Darker 1142O156DB 1 4 7 2 5 8 0 3 6 9 C 1142O171AA Using the Multi-Copy Keys, enter the number of copies to be made. * The maximum number that can be Example: To make 18 copies, press Key and then Key , in that order. The Multi-Copy Display now shows "18. " 1139O3740A Correcting the Number Entry 1 4 7 2 5 8 0 3 6 9 C 1142O169AA To correct or reset a number entry, press the Clear Key. * The Multi-Copy Display is reset to "1. " 1139O3750A Making Copies set is 99. Chapter 3 Setting the Number of Copies 48 2. Copying Procedure Starting the Copy Cycle 1 Meter Count Toner Drum Dehumidify 2 5 8 0 Start 3 6 9 C Stop Panel Reset Energy Saver % Paper 4 7 A4 Auto 50%~200% 141% 115% 100% 81% 70% A4 A3 B4 A3 Full Size B4 A4 A3 A4 100% Auto Size Sort Book Lighter A Darker 1142O156DB Chapter 3 Starting the Copy Cycle Making Copies 1 2 1139O2360A Check the control panel to make sure that you have set up your copy job correctly. In a multi-copy cycle, the number on the Multi-Copy Display is decreased by 1 each time a copy is fed out of the copier. The Display is reset to the original setting as soon as the multi-copy cycle is completed. The Multi-Copy Display shows the number of copies yet to be made. Stopping a Multi-Copy Cycle Stop 1139O2592A 1139O2592A 49 2. Copying Procedure Manual Bypass Copying Use the Manual Bypass to make copies on paper not loaded in the Drawer, or to copy onto transparencies, translucent paper, or any other special paper. If the copier is equipped with a Multi Bypass Table (option), you can load more than one sheet of paper for a continuous run. x Types of Paper · Plain paper (weighing 60 g to 90 g/m 2) · Heavyweight paper (weighing 90 g to 157 g/m2) · Transparencies, translucent paper x Paper Size · Width: 100 mm to 297 mm · Length: 140 mm to 432 mm x Capacity · Plain paper, heavyweight paper, transparencies, translucent paper . . . 1 sheet at a time Using the Manual Bypass Table 1 2 1139O0150A Place the original on the Original Glass and make the control panel settings. x This automatically starts the copy cycle. NOTES · Insert the copy paper one sheet at a time. · Do not insert a sheet of paper while the copier is warming up or in a multi-copy cycle. · The Auto Size Mode and Book Copying Mode cannot be selected for manual bypass copying. Making Copies <Multi Bypass Table> · Plain paper: Approx. 50 sheets · Heavyweight paper, transparencies, translucent paper: Approx. Copying Procedure Using the Multi Bypass Table (Option) 1 2 1139O0130A Place the original on the Original Glass and make the control panel settings. Swing down the Multi Bypass Table and slide the Paper Guide Plate to the size of the copy paper. NOTE Pull out the Multi Bypass Table Extender if you are using larger paper. Chapter 3 Making Copies 3 1139O0140A Place a neat stack of copy paper on the Table and insert it into the copier until it stops. NOTES · Before inserting, fan the paper stack well if you are using transparencies or translucent paper. · Correct any curl if you are using heavyweight paper. 4 5 1139O2360A Using the Multi-Copy Keys, enter the number of copies to be made. 48 NOTES · Do not insert the paper while the copier is in the warm-up cycle or a multi-copy cycle. · The Auto Size and Book Copying Mode cannot be selected for manual bypass copying. 51 Chapter 4 Auxiliary Functions This Chapter explains about the Auxiliary functions that can be used for specific purposes. Chapter 4 1. [. . . ] Action It could result in the copier or other electrical equipment malfunctioning. Turn the copier OFF immediately, unplug the power cord, and call your Technical Representative. * Communications Cable: Cable connecting the copier with options Original Glass Item Is the Glass dirty?Action Clean the Glass using the procedure given in "Cleaning. " p. Is the Glass cracked or chipped? Chapter 8 Miscellaneous 111 1. [. . . ]