User manual KONICA MINOLTA IC-304 CREO

[. . . ] The essentials of imaging IC-304 Print Controller for bizhub PRO C6500 Printer Version 1. 0 User Guide English 731-00952A-EN Rev A Copyright © 2007 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. This document is also distributed in Adobe Systems Incorporated's PDF (Portable Document Format). Copies produced from the PDF file must be reproduced in whole. Trademarks KONICA MINOLTA, the KONICA MINOLTA logo, and The essentials of imaging are registered trademarks of KONICA MINOLTA HOLDINGS, INC. bizhub and bizhub PRO are registered trademarks of KONICA MINOLTA BUSINESS TECHNOLOGIES. [. . . ] To save the locations and text of the tabs that you created, select the Include Tab location and Caption check box. Note: If you do not select this check box, only the text attribute settings are saved. 4. Click Save. To apply saved settings to a job: In the Tabs Printing window, select the settings from the Saved Settings list. The saved settings are applied to the job. Tip: You can modify any of the settings as desired. To delete saved settings: 1. 2. In the Tabs Printing window, select the saved settings from the Saved Settings list. The saved settings are deleted. 118 Chapter 6--Production Printing Color Workflow Calibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120 Color Tools. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126 120 Chapter 7--Color Workflow Calibration One of the most important issues in obtaining satisfactory print quality is steady toner density. Toner density is affected by many factors such as heat, humidity, and service settings. You should perform calibration every 24 hours to compensate for these factors. The calibration process corrects the printer colors by measuring their density and creating calibration look-up tables. The IC-304 print controller uses the data in these tables to compensate for the differences between the actual, measured density level and the target level, the target density. You should perform calibration in the following instances: · When prints show "color casts" · After machine maintenance or hardware changes--for example, replacing a "Charge Coroton" · On drastic ambient changes (temperature and humidity) Color Calibration Method The IC-304 print controller uses the target calibration method. This method ensures consistency over time and that the density values of the printed output do not exceed the predefined density values. Target calibration enables you to calibrate the bizhub PRO C6500 printer according to the following predefined density values: Table 11: Fixed density values for uncoated paper Toner Density value Cyan Magenta Yellow Black 1. 3426 1. 4669 0. 9246 1. 7603 Calibration 121 Table 12: Fixed density values for coated paper Toner Density value Cyan Magenta Yellow Black 1. 6930 1. 7706 1. 1949 1. 9838 Choosing a Calibration Mode The IC-304 print controller provides you with two calibration modes: · Off-the-glass: Uses the scanner platen to perform off-the-glass calibration · Densitometer: Uses the DTP34 densitometer, which is a "high speed" color measurement instrument, to report densitometer and dot data You select the calibration mode in the Preferences window, see "Calibration Device" on page 167. 122 Chapter 7--Color Workflow General Tips and Guidelines Perform the following steps on the IC-304 print controller to ensure a successful calibration process: 1. Perform the auto gradation adjustment procedure. a. b. On the control panel touch screen, press MACHINE and then Adjustment. From the Adjustment menu, choose Execute Adjust Operation. The Execute Adjust Operation options appear. c. The IC-304 print controller performs the auto gradation adjustment. Note: The auto gradation adjustment procedure may take a few minutes. 2. Choose a coated glossy offset as your media. Press OK. You can now begin the calibration process. Calibration 123 Calibration Process This section describes the off-the glass calibration process. If you want to use the DTP34 densitometer to calibrate, refer to the X-Rite DTP34 Densitometer Operator's Manual and follow the IC-304 print controller calibration wizard Note: It is recommended that: 1. After you perform the first calibration, you print the IQ_Test_(TAB/A3). pdf file from the D:\Sample_Files\(USA/Europe)\IQ Files folder. Each time you calibrate, use this file as a visual reference to verify that the printer has returned to its start point. If you only place the print chart on the platen, the printer is calibrated. If you only place the scanner chart on the platen, the scanner is calibrated. 2. 1. On the toolbar, click Calibration. 2. In the Tray list, select the desired tray. You can print the calibration chart on any paper size that is equal to or larger than A4 or Letter. 124 Chapter 7--Color Workflow 3. In the Media Type list, select the desired media type--for example, Coated. When this option is selected, your job is printed on the media type that is defined on the bizhub PRO C6500 printer. [. . . ] An additional separation (fifth, or more) that is used with special inks to achieve difficult color combinations, such as gold, or chocolate brown. Spot color is sometimes used by graphic artists to define special corporate colors, for example, for company logos. On the IC-304 print controller, spot colors are translated into CMYK values using a dictionary, that can be edited to adjust CMYK values. The procedure of copying the same image by stepping it in position both horizontally and vertically according to a predetermined layout. [. . . ]