User manual KONICA MINOLTA MAGICOLOR 2530 DL

[. . . ] magicolor 2530 DL User's Guide ® A00V-9566-00A 1800818-001A Thank You Thank you for purchasing a magicolor 2530 DL. Your magicolor 2530 DL is specially designed for optimal performance in Windows, Macintosh, and other environments. Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. magicolor is a trademark or registered trademark of KONICA MINOLTA PRINTING SOLUTIONS U. S. A. , INC. Copyright Notice Copyright © 2006 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. , Marunouchi Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Notice KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. [. . . ] If the duplex option is not installed and duplex job is sent, the control panel will display DUPLEX UNIT NOT ATTACHED. Check your application to determine how to set your margins for duplex printing. If "Short Edge Binding" is selected, the pages will be laid out to flip at the top. 11 2 11 Duplexing 2 13 If "Long Edge Binding" is selected, the pages will be laid out to flip at the sides. 13 63 2 1 If "Booklet Left Binding" is selected, the pages can be folded as a left-bound booklet. 1 3 3 1 If "Booklet Right Binding" is selected, the pages can be folded as a right-bound booklet. 2 3 1 1 2 3 Load plain paper into the tray. " With autoduplexing, the back side is printed first, and then the front side is printed. Output Tray All printed media is output to the face-down output tray on top of the printer. This tray has a capacity of approximately 200 sheets (A4/Letter) of 80 g/m2 (22 lb) paper. !" If the media is stacked too high in the output tray, your printer may experience media misfeeds, excessive media curl, or static buildup. Remove transparencies as soon as possible from the output tray to avoid static buildup. 64 Output Tray Media Storage How do I store media? !Keep media on a flat, level surface in its original wrapper until it is time to load it. Media that has been stored for a long time out of its packaging may dry up too much and cause misfeeding. !If media has been removed from its wrapper, place it in its original packaging and store in a cool, dark place on a level surface. !Avoid moisture, excessive humidity, direct sunlight, excessive heat (above 35°C [95°F]), and dust. !Avoid media leaning against other objects or placing it in an upright position. Before using stored media, do a trial print and check print quality. Media Storage 65 Replacing Consumables 7 Replacing Consumables Note Failure to follow instructions as outlined in this manual could result in voiding your warranty. About Toner Cartridges Your printer uses four toner cartridges: black, yellow, magenta, and cyan. Handle the toner cartridges carefully to avoid spilling toner inside the printer or on yourself. !If a used toner cartridge is installed, the indicator message will not clear and the supplies status in the Status Display will not be updated. If you get toner on your skin, wash it off with cool water and a mild soap. If you get toner on your clothes, lightly dust them off as best as you can. If some toner remains on your clothes, use cool, not hot water, to rinse the toner off. CAUTION If you get toner in your eyes, wash it out immediately with cool water and consult a doctor. !Americas:http://printer. konicaminolta. net/products/recycle/index. asp Europe:http://www. minolta-qms. nl/nlen/frames/cleanplanet. htm Do not use refilled toner cartridges or unapproved toner cartridges. Any damage to the printer or quality problems caused by a refilled toner cartridge or unapproved toner cartridge will void your warranty. No technical support is provided to recover from these problems. 68 Replacing Consumables When replacing a toner cartridge, refer to the following table. For optimum print quality and performance, use only approved KONICA MINOLTA toner cartridges for your specific printer type, as listed in the table below. [. . . ] Before performing this procedure, review the antistatic caution on Page 126. In addition, always handle circuit boards by the edges only. 1 Turn off the printer and disconnect the power cord and interface cables. !" If the duplex option is installed, remove it. 128 Dual In-Line Memory Module (DIMM) 2 Using a screwdriver, remove the screw on the back of the printer. 3 Remove the rear panel. !" Since there are two hooks on the right side of the panel, remove the rear panel by slightly pulling the left side of the panel toward you, then sliding the panel off to the left. 4 Insert the new DIMM straight into the DIMM connector until the latches snap into the locked position. [. . . ]