User manual KONICA MINOLTA MAGICOLOR 7450 II

[. . . ] User's Guide 4039-9571-00A Thank You Thank you for purchasing a magicolor 7450II. Your magicolor 7450II is specially designed for optimal performance in Windows, Macintosh and Linux environments. Trademarks KONICA MINOLTA and the KONICA MINOLTA logo are trademarks or registered trademarks of KONICA MINOLTA HOLDINGS, INC. magicolor and PageScope are trademarks or registered trademarks of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. All other trademarks and registered trademarks are the property of their respective owners. Copyright Notice Copyright © 2008 KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. , Marunouchi Center Building, 1-6-1 Marunouchi, Chiyoda-ku, Tokyo, 100-0005, Japan. This document may not be copied, in whole or part, nor transferred to any other media or language, without written permission of KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. Notice KONICA MINOLTA BUSINESS TECHNOLOGIES, INC. [. . . ] Banner Paper Weight: 127-160 g/m2 Width: 210-297 mm Length: 458-1200 mm Media Types 89 DO NOT use thick stock that is Mixed with any other media in Tray 1 (as this will cause printer misfeeding) Envelopes Print on the front (address) side only. Some parts of the envelope consist of three layers of paper--the front, back, and flap. Tray 1 Up to 10 envelopes, depending on their (Manual Feed thickness Tray) Tray 2 Up to 10 envelopes, depending on their thickness Tray 3/4/5 Not supported Orientation Tray 1 Face down (Manual Feed Tray) Tray 2 Face up Tray 3/4/5 -- Driver Envelope Media Type Weight 64­163 g/m² (17­43 lb bond) Duplexing Not supported Use envelopes that are Common office envelopes approved for laser printing with diagonal joints, sharp folds and edges, and ordinary gummed flaps Because the envelopes pass through heated rollers, the gummed area on the flaps may seal. Approved for laser printing Dry DO NOT use envelopes that have Sticky flaps Tape seals, metal clasps, paper clips, fasteners, or peel-off strips for sealing Transparent windows Capacity 90 Media Types Too rough of a surface Material that will melt, vaporize, offset, discolor, or emit dangerous fumes Been presealed Media Types 91 Labels A sheet of labels consists of a face sheet (the printing surface), adhesive, and a carrier sheet: The face sheet must follow the plain paper specification. The face sheet surface must cover the entire carrier sheet, and no adhesive should come through on the surface. However, this could affect the media feed, depending on the media quality and printing environment. If problems occur, stop the continuous printing and print one sheet at a time. Try printing your data on a sheet of plain paper first to check placement. Check your application documentation for more information on printing labels. Capacity Tray 1 Up to 10 label sheets, depending on their (Manual Feed thickness Tray) Tray 2 Up to 50 label sheets, depending on their thickness Tray 3/4/5 Not supported Orientation Tray 1 Face down (Manual Feed Tray) Tray 2 Face up Tray 3/4/5 -- Driver Label Media Type Weight 64­163 g/m² (17­90 lb) Duplexing Not supported Use label sheets that are Recommended for laser printers DO NOT use label sheets that Have labels that easily peel off or have parts of the label already removed Have backing sheets that have peeled away or have exposed adhesive Labels may stick to the fuser, causing them to peel off and media misfeeds to occur. 92 Media Types Are precut or perforated Do not use OK to use Shiny backed paper Full-page labels (uncut) Letterhead Try printing your data on a sheet of plain paper first to check placement. Tray 1 Up to 10 sheets, depending on their size and (Manual Feed thickness Tray) Tray 2 Up to 50 sheets, depending on their size and thickness Tray 3/4/5 Not supported Orientation Tray 1 Face down (Manual Feed Tray) Tray 2 Face up Tray 3/4/5 -- Driver Letterhead Media Type Weight 64­90 g/m² (17­24 lb) Duplexing Not supported Capacity Postcards Try printing your data on a sheet of plain paper first to check placement. Capacity Tray 1 Up to 10 postcards, depending on their (Manual Feed thickness Tray) Tray 2 Up to 50 postcards, depending on their thickness Tray 3/4/5 Not supported Media Types 93 Orientation Driver Media Type Weight 64­163 g/m² (17­90 lb) Duplexing Not supported Use postcards that are Approved for laser printers DO NOT use postcards that are Coated Designed for inkjet printers Precut or perforated Preprinted or multicolored Tray 1 Face down (Manual Feed Tray) Tray 2 Face up Tray 3/4/5 -- Postcard If the postcard is warped, press on the warped area before putting it in Tray 1/2. Transparencies Do not fan transparencies before loading them. If you touch the face of the transparencies with your bare hands, print quality may be affected. If there are shadows on either the top or the bottom of the sheets, see chapter 8, "Maintaining the Printer" . Remove transparencies as soon as possible from the output tray to avoid static buildup. However, this could affect the media feed, depending on the media quality, static buildup, and printing environment. Try printing your data on a sheet of plain paper first to check placement. 94 Media Types If you have problems feeding 20 sheets, try loading only 1­10 sheets at a time. Loading a large number of transparencies at one time may cause static buildup, thus causing feeding problems. Tray 1 Up to 10 transparencies, depending on their (Manual Feed thickness Tray) Tray 2 Up to 50 transparencies, depending on their thickness Tray 3/4/5 Not supported Orientation Tray 1 Face down (Manual Feed Tray) Tray 2 Face up Tray 3/4/5 -- Driver Transparency, Transparency2 Media Type Transparency2 is a suitable setting for CG3700 of 3M. Duplexing Not supported Always first test a small quantity of a particular type of transparency. Use transparencies that are Approved for laser printing DO NOT use transparencies that Have static electricity that will cause them to stick together Are specified for inkjet printers only Capacity Glossy Stock Test all glossy stock to ensure acceptable performance and to ensure that the image does not shift. Capacity Up to 10 glossy stock sheets, depending on Tray 1 (Manual Feed their thickness. [. . . ] Do not remove the tape securing the relay harness on the lower feeder unit until the unit is connected to the machine. Lower Feeder Unit 215 4 Attach the upper cover to the second and subsequent lower feeder units. If only one lower feeder unit was installed, do not install the upper cover. 5 If multiple lower feeder units are to be installed, stack them together. 6 Use a screwdriver to attach the two securing brackets to the rear of the trays in order to secure the lower feeder units together. 216 Lower Feeder Unit 7 Pull out the trays, and then use a screwdriver to attach the two securing brackets in order to secure the lower feeder units together. 8 With another person's help, place the printer on top of the lower feeder unit, making sure that the positioning pins on the lower feeder unit correctly fit into the holes on the bottom of the printer. 59 kg 129. 9 lbs If two or three lower feeder units are to be installed, stack the lower feeder units and secure them together before installing them to the printer. When placing the printer on the optional tray unit, align the front and back of the printer and the unit. Lower Feeder Unit 217 WARNING! Lifting the printer in an awkward position or transporting it in a poorly balanced position could result in personal injury. When transporting the printer, assign an adequate number of persons to the job and ensure that each person can take a good position of not being excessively loaded. [. . . ]