User manual KONICA MINOLTA MS7000 MKII

[. . . ] Installation and User's Guide For Konica Minolta Business Solutions' TWAIN Driver V. 5. 0. 1. 7b & Overlay Manager Software September 10, 2004 Section 1 - Overview & Hardware Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 HARDWARE INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Section 2 ­Software Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 THE TWAIN DRIVER USER INTERFACES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To use previewing to define a custom area, first click the Preview button, once an image has been placed in the preview window just drag and drop or resize the scan area to match the given portion of the preview image you wish to capture. Cancel ­ Use the Cancel button to close out the driver window without initiating any scans. Help ­ Clicking the Help button will launch the TWAIN driver help file. Much of the information contained in this guide can be found within the Help file. This box contains important information including the current driver version number. This is the most reliable means for determining which version of the driver you are running. Section 5 - TWAIN Configuration Utility & Status Window The TWAIN configuration Utility and Status Window are launched and displayed every time the driver installation routine is executed. The purpose of these utilities is to scan your SCSI buses, locate all eligible attached Minolta scanners and then install the correct drivers/data sources. In addition, the Status Window provides a quick snapshot of your current system configuration (think of it as a Windows Explorer for your Minolta SCSI devices and TWAIN data sources). Detected SCSI Adapters A detected Minolta scanner that is correctly connected to the PC on Host Adapter 2. A red X means that the associated hardware is not connected or detected. An MS 6000 connected on Adapter 2 with SCSI ID of 3 Installed TWAIN Data Sources The driver has a blue highlight when selected. When any installed driver is selected the Remove button is activated. If an active driver is selected the Properties button becomes active. The Status Window shows a host of information pertaining to your system. The first level of the status window shows all the detected SCSI Host Adapters on your PC. In addition, the Status Window will show any connected Minolta scanners. They will be listed under the Host Adapter to which they are connected. The scanner's name will be shown as well as the channel and SCSI ID associated with the scanner. The last line of the Status Window will show a list of all installed TWAIN drivers/data sources. Each driver lists the model name of the scanner and is followed by the "@" symbol and three numbers. These three numbers, which are captured during the configuration scan, are 1) the SCSI Adapter the scanner is (was) attached to; 2) the channel associated with it and; 3) the SCSI ID of the scanner. If two same-model machines are connected to the same PC with different SCSI IDs or on different SCSI adapters, the configuration utility will actually create two separate data sources/drivers. This is done to ensure that multiple scanners of the same model can be attached and managed at one time without any conflicts. Once a driver is installed it will remain on the system even if the applicable scanner is later disconnected. Any driver with the hardware currently not attached or detected will be shown with a red X through the scanner icon. Refresh ­ The Refresh button can be pressed to launch the TWAIN configuration utility and to rescan the SCSI bus. Add - The Add button is not currently used with the Minolta TWAIN drivers. Remove ­ The Remove button will become active whenever a listed driver is selected and the associated hardware of that driver is currently connected and detected. Once a driver is selected you can press the Remove button to delete that driver from your system. [. . . ] The Window ­ The preview window itself represents the entire 11"x17" scan area of the PS 3000. Within the preview window will be an outlined rectangle (or two rectangles in dual scan mode). This outline represents the actual area that the scanner is currently set to capture. This outline can be changed by selecting a preset paper size from the Paper Size drop-down box. [. . . ]