User manual KONICA MINOLTA PI4700E UM DRIVER 1.1.0

[. . . ] User Manual Pi4700e www. minoltaeurope. com The essentials of imaging Windows Driver, Convenient Functions Table of Contents Welcome . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-1 Trademark Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-1 Limited Software Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . X-2 Minolta Network Card Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Fit to Paper cannot be selected if Custom Paper is selected in Original Document Size. è è 3. Setting range: 1 to 999 sets NOTE è When using the OHP interleaving function, set the number of sets of prints to 1. 4. Collate Use this function when making multiple sets of prints of the same document, to specify whether or not to print one set at a time. For example, if you make five sets of prints, each page is printed in sequence five copies at a time. 1-22 Pi4700e - MS-Windows-Driver Properties Settings m 1 Collated Prints are output one set at a time. For example, if you make five sets of prints of a 10-page document, the prints will be output one set at a time. NOTE è Keep Collate (Sort) on the application side set to "OFF" at all times. 5. m Sorted Prints are sorted. TIP If you output prints to the Elevator Tray when the Single-staple Finisher, Multi-staple Finisher or Mailbin Finisher is installed, the prints are output in a sawtooth manner. When the Folding Finisher is installed or if none of the finishing options is installed, the prints are output in a criss-cross manner. The following are the minimum requirements for permitting crisscross sorting using the Collated setting: Stacks of paper of the same size are loaded in the lengthwise and crosswise directions. m Landscape Printing takes place crosswise. TIP A Portrait or Landscape print appears on the Page Layout. Pi4700e - MS-Windows-Driver 1-23 1 Properties Settings Functions of the Edit Custom Paper or Custom Paper dialog box The name of the dialog box is Custom Paper for PCL6, Edit Custom Paper for PS. Use this dialog box to set special sizes of paper. 1 2 3 4 1. When it is selected, the dialog box changes to the Custom Paper Setting Dialog Box. Number of registrations: Depending on environment used, number of registrations will be different. When it is selected, the dialog box changes to the Custom Paper Setting Dialog Box. Delete Deletes Custom Paper selected in (1). 1-24 Pi4700e - MS-Windows-Driver Properties Settings 1 Edit Custom Paper Setting dialog box (PS version) Custom Paper Setting dialog box (PCL 6 version) 5 6 7 5 6 5. Name Enter the Name of the Custom Paper Setting range: Max 20 characters 6. Setting range: Width: 4 to 11 11/16 (Unit = inch) 100 to 297 (Unit = mm) Height: 5 13/16 to 17 (Unit = inch) 148 to 432 (Unit = mm) 7. Unit Switches input units of paper size between inch and metric. Pi4700e - MS-Windows-Driver 1-25 1 1. 6 Quality tab PCL6 version Properties Settings 2 1 1. Available settings: On, Off NOTE è This function is used with a document whose contents are mainly text. Using the function with a photo image could even dirty the produced image. 1-26 Pi4700e - MS-Windows-Driver Properties Settings PS version 1 1 2 4 3 5 1. m Mirror Reverses left and right. Pi4700e - MS-Windows-Driver 1-27 1 Functions of the Halftoning dialog box Properties Settings 1 2 3 1. User Printer's settings: Uses the setting value of the printer when the halftone image is printed. m Use settings below: Uses the optional setting value (the setting of optional value) instead of the setting value of the printer when the halftone image is printed. [. . . ] Using the settings stored for a current print job 1 Start printing from the application which has been used to create the document: Normally, printing can be started by selecting Print from the File menu. 2 The Print dialog box will appear. Make sure that Minolta Di470 PCL6 is displayed for Name in Printer, and click the Properties button. NOTE è Some Applications allow you to set Copies and Collate (Sort) in the Print dialog box. To ensure proper printing operation, however, turn OFF these items of the application, and make the necessary settings in each tab of the printer driver. 3 The Minolta Di470 PCL6 dialog box will appear. 2-30 4 Click the down-arrow of Easy Set Name and from subsequent menu, select the Title name to be used. Pi4700e - MS-Windows-Driver Convenient Functions 2 5 Dialog box for confirmation will appear. The setting data will then be read to the driver software. 6 Click the OK button. 8 The data will then be transferred to the machine and printing will soon start. Pi4700e - MS-Windows-Driver 2-31 2 Storing settings Convenient Functions 1 Start printing from the application which has been used to create the document: Normally, printing can be started by selecting Print from the File menu. 2 The Print dialog box will appear. Make sure that Minolta Di470 PCL6 is displayed for Name in Printer, and click the Properties button. NOTE è Some Applications allow you to set Copies and Collate (Sort) in the Print dialog box. [. . . ]