User manual KRESS 850 SB-2

[. . . ] 3) PERSONAL SAFETY a) Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. [. . . ] Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. , in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. 5) SERVICE a) Have your power tool serviced by a qualified repair person using only identical replacement parts. SAFETY INSTRUCTIONS FOR IMPACT DRILLS Wear ear protectors with impact drills (exposure to noise can cause hearing loss) Use auxiliary handles supplied with the tool (loss of control can cause personal injury) Hold the power tool only by the insulated gripping surfaces when performing an operation where the accessory may contact hidden wiring or its own power cord (contact with a "live" wire will also make exposed metal parts of the power tool "live" and shock the operator); always use auxiliary handle F3 4 5 6 Use suitable detectors to find hidden utility lines or call the local utility company for assistance (contact with electric lines can lead to fire or electrical shock; damaging a gas line can result in an explosion; penetrating a water pipe will cause property damage or an electrical shock) Avoid damage that can be caused by screws, nails and other elements in your workpiece; remove them before you start working Always keep the cord away from moving parts of the tool Secure the workpiece (a workpiece clamped with clamping devices or in a vice is held more securely than by hand) When you put away the tool, switch off the motor and ensure that all moving parts have come to a complete standstill Use completely unrolled and safe extension cords with a capacity of 16 Amps (U. K. 13 Amps) In case of electrical or mechanical malfunction, immediately switch off the tool and disconnect the plug KRESS can assure flawless functioning of the tool only when original accessories are used Use only accessories with an allowable speed matching at least the highest no-load speed of the tool This tool should not be used by people under the age of 16 years Do not work materials containing asbestos (asbestos is considered carcinogenic) Dust from material such as paint containing lead, some wood species, minerals and metal may be harmful (contact with or inhalation of the dust may cause allergic reactions and/or respiratory diseases to the operator or bystanders); wear a dust mask and work with a dust extraction device when connectable Certain kinds of dust are classified as carcinogenic (such as oak and beech dust) especially in conjunction with additives for wood conditioning; wear a dust mask and work with a dust extraction device when connectable Follow the dust-related national requirements for the materials you want to work with If the cord is damaged or cut through while working, do not touch the cord, but immediately disconnect the plug Never use the tool when cord is damaged; have it replaced by a qualified person Always check that the supply voltage is the same as the voltage indicated on the nameplate of the tool (tools with a rating of 230V or 240V can also be connected to a 220V supply) If the drill bit becomes unexpectedly jammed (causing a sudden, dangerous reaction), immediately switch off the tool Be aware of the forces that occur as a result of jamming (especially when drilling metals); always use auxiliary handle F 3 4 5 6 and take a secure stance Always disconnect plug from power source before making any adjustment or changing any accessory WHEN CONNECTING NEW 3-PIN PLUG (U. K. ONLY): Do not connect the blue (= neutral) or brown (= live) wire in the cord of this tool to the earth terminal of the plug If for any reason the old plug is cut off the cord of this tool, it must be disposed of safely and not left unattended USE On/off 7 Switch locking for continuous use 8 Speed control for smooth starting 9 Maximum speed control 0 - switch on the tool - lock the switch - turn wheel C to select maximum speed 11 Changing direction of rotation !- when not properly set in left/right position, switch A cannot be activated !change direction of rotation only when tool is at a complete standstill Normal drilling/screwdriving versus impact drilling @ !select drilling function only when tool is switched off and plug is disconnected Changing bits # $ - insert the bit as deep as possible in the chuck !do not use bits with a damaged shank Adjusting drilling depth % Holding and guiding the tool ^ !Fascicolo tecnico presso: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. H CE MINSGI TANUSTVNY Teljes felelssgnk tudatban kijelentjk, hogy jelen termk a kvetkez szabvnyoknak vagy ktelez hatsgi elrsoknak megfelel: EN 60 745, EN 55 014, a 2006/95/EK, 2004/108/EK, 98/37/EK (2009. 12. 28-ig), 2006/42/EK (2009. 12. 29-tl kezdve) elrsoknak megfelelen. ZAJ/REZGS Az EN 60 745 alapjn vgzett mrsek szerint ezen kszlk hangnyoms szintje 94 dB(A), hangteljestmny szintje 105 dB(A) (norml eltrs: 3 dB) a rezgsszm m/s2 (kzre-hat rtk). A mszaki dokumentci a kvetkez helyen tallhat: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. CZ CE STRVZUJC PROHLSEN Potvrzujeme na odpovdnost, ze tento vrobek odpovd nsledujcm normm nebo normativnm podkladm: EN 60 745, EN 55 014, podle ustanoven smrnic 2006/95/ES, 2004/108/ES, 98/37/ES (do 28. 12. 2009), 2006/42/ES (od 29. 12. 2009). HLUCNOSTI/VIBRAC Meno podle EN 60 745 cin tlak hlukov vlny tohoto pstroje 94 dB(A), dvka hlucnosti 105 dB(A) (standardn odchylka: 3 dB) a vibrac m/s2 (metoda ruka-paze). Technick dokumentace u: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. TR CE STANDARDIZASYON BEYANI Yeane sorumlu olarak, bu rnn aaidaki standartlara veya standart belgelerine uygun olduunu beyan ederiz: EN 60 745, EN 55 014, ynetmelii hkmleri uyarinca 2006/95/EG, 2004/108/EG, 98/37/EG (28. 12. 2009 tarihine kadar), 2006/42/EG (29. 12. 2009 tarihinden itibaren). GRLT/TTREIM llen EN 60 745 gre ses basinci bu makinanin seviyesi 94 dB(A), alima sirasindaki grlt 105 dB(A) (standart sapma: 3 dB) ve titreflim m/s2 (el-kol metodu). Teknik belgelerin bulunduu merkez: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. PL OWIADCZENIE ZGODNOCI CE Niniejszym owiadczamy ponoszc osobist odpowiedzialno, e produkt wykonany jest zgodnie z nastpujcymi normami i dokumentami normalizujcymi: EN 60 745, EN 55 014, z godnie z wytycznymi 2006/95/EU, 2004/108/EU, 98/37/EU (do 28. 12. 2009), 2006/42/EU (od 29. 12. 2009). HALASU/WIBRACJE Pomiarw dokonano zgodnie z norm EN 60 745 cinienie akustyczne narzdzia wynosi 94 dB(A), poziom mocy akustycznej 105 dB(A) (poziom odchylenie: 3 dB) za wibracje m/s2 (metoda dlo-rka). Dokumentacja techniczna: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. RU , : EN 60 745, EN 55 014, 2006/95/EC, 2004/108/EC, 98/37/EC ( 28. 12. 2009), 2006/42/EC ( 29. 12. 2009). / co o EN 60 745 94 (A), e - 105 (A) ( : 3 dB) /2 ( ). CE , : EN 60 745, EN 55 014, 2006/95/EG, 2004/108/EG, 98/37/EG 28. 12. 2009 p. ), 2006/42/EG ( 29. 12. 2009 p. ). [. . . ] BUCI/VIBRACIJAMA Mjereno prema EN 60 745 prag zvucnog tlaka ovog elektricnog alata iznosi 94 dB(A), jakost zvuka 105 dB(A) (standardna devijacija: 3 dB) a vibracija m/s2 (postupkom na saci-ruci). Tehnicka dokumentacija se moze dobiti kod: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. SRB CE IZJAVA O USKLA ENOSTI Pod punom odgovornosu izjavljujemo da je ovaj proizvod usklaen sa sledeim standardima ili standardizovanim dokumentima: EN 60 745, EN 55 014, u skladu sa odredbama smernica 2006/95/EG, 2004/108/EG, 98/37/EG (do 28. 12. 2009), 2006/42/EG (od 29. 12. 2009). BUKA/VIBRACIJE Mereno u skladu sa EN 60 745 nivo pritiska zvuka ovog alata iznosi 94 dB(A), jacina zvuka 105 dB(A) (normalno odstupanje: 3 dB) a vibracija m/s2 (mereno metodom na saci-ruci). Tehnicka dokumentacija kod: KRESS Europe BV (PT-SEU/PJE), 4825 BD Breda, NL. SLO IZJAVA O USTREZNOSTI CE Odgovorno izjavljamo, da je ta izdelek v skladu z naslednjimi standardi ali standardnimi dokumenti: EN 60 745, EN 55 014, v skladu s predpisi navodil 2006/95/ES, 2004/108/ES, 98/37/ES (do 28. 12. 2009), 2006/42/ES (od 29. 12. 2009). [. . . ]