User manual KURZWEIL KME61 REV A

[. . . ] Kurzweil is a product line of Young Chang Co. ; Kurzweil and KME61 are trademarks of Young Chang Co. All other products and brand names are trademarks or registered trademarks of their respective companies. Product features and specifications are subject to change without notice. Part Number:910383-001 Rev. A The Kurzweil KME61 User's Guide CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with the arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. IMPORTANT SAFETY & INSTALLATION INSTRUCTIONS INSTRUCTIONS PERTAINING TO THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS WARNING: When using electric products, basic precautions should always be followed, including the following: 1. [. . . ] Pressing + and ­ at the same time clears transposition to Oct:0 and Key:C. The Channel and Transpose setting are remembered as long as the KME61 is in Program Mode. When you select Setup Mode, the setup parameters govern channel(s) and transposition. When returning to Program Mode, they revert to what they were when Program Mode was exited. When you turn on your KME61, Channel is set to 1 and Transposition is set to Octave:0 and Key:C. Editing a Program Program Mode has two Edit Pages for setting up the effects. Unlike the Base Page edits for Channel and Transpose, these edits can be made permanent and saved with the sound program. To access the Program Mode Edit Pages, press the Program Mode button again. To leave the Program Mode Edit Pages, press the Program Mode button again. If 3-2 Program Mode changes were made, the Program Save Dialog is executed first (see below). Otherwise the display will immediately change back to Program Mode Base Page and the Program Mode LED will stop flashing. Edit Effect Type 16 Hall:Chorus The first Program Mode Edit Page is for selecting the Effect Type (program). There are 30 Effect Types, each with a unique combination of an A Effectand a B Effect. The number and name of the currently selected Effect Type are displayed on the bottom line of the LCD. The + and - buttons or Data Slider may be used to scroll through the list of choices. Edit Effect Levels A: 5% B: 10% Edit Effect Levels A: 5% B: 10% The second Program Mode Edit Page is for adjusting the wet/dry mix for the A and B effects separately. The arrow ">" indicates which parameter you are adjusting. You can move the arrow to the A or B parameter by using the up and down menu buttons. The +/- buttons or Data Slider are used to adjust the level which is pointed by the arrow. Restoring the Default Effects Parameters For either of these edit screens, pressing + and ­ at the same time will bring up this page: Reload default prog?Yes Cancel Pressing the left soft button (Yes) will cause the original factory settings for Effect Type and Effect Levels for the current program to be reloaded. Pressing the right soft button (Cancel) brings back the previous display. Saving Your Edited Program To leave Program Mode Edit, press the Program Mode button (which is still flashing). If the Effect Type or FX levels were changed from their previous values (including reloading the defaults), the Program Save Dialog is executed first as shown below. If no changes have been made, the dialog is skipped, the Program Mode Base page is displayed and the Program Mode LED stops flashing. Save Current Prog?Yes No Cancel The right soft button (Cancel) will cancel the exit and return the display to the previous edit page. The center soft button (No) will discard the changes to Effect Type and Effect levels then return the display to the Program Mode Base page. [. . . ] You also set the effects parameters for each of the 256 sounds while editing the Program. Program Parameters Below is a list of the parameters and default values for the Program Mode. The shaded parameters are not available in Program mode. The default values of the effects parameters vary according to which sound is selected. ZONE 1 Sound Group and Program - According to sound selected Key Range Low - C2 Key Range High - C6 Vel. Range High - 127 Note Shift - Initially 0 then as edited Volume - 127 FXA Level - According to sound selected then as edited FXB Level - According to sound selected then as edited MIDI Channel - Initially 1 then as edited MIDI Program - According to sound selected MIDI Bank According to sound selected Zone Mutes - On FX Type - According to sound selected ZONE 2 None None None None Off ZONE None None None None Off Program List Below is a list of the 256 sounds (Programs) available from the internal sound module. The list includes the control assignment and the factory default effects setting for each sound. Reference Group A Piano 1 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Stereo Grand Classical Grand Dynamic Grand Warm Grand Solo Grand Piano Concert Piano Mono Grand Piano Piano for layers Sweet Ivories Nice Touch Grand Piano Solitude Piano Recital Full Bloom Piano Pianetta Suite Piano Dreamy Piano Data Slider MW Mpress Data Slider MW Mpress FX Type 4. [. . . ]