User manual LA CROSSE TECHNOLOGY WS-9025U

[. . . ] This handbook must not be reproduced in any form, even in excerpts, or duplicated or processed using electronic, mechanical or chemical procedures without written permission of the publisher. The information in this handbook is regularly checked and corrections made in the next issue. We accept no liability for technical mistakes or printing errors, or their consequences. All trademarks and patents are acknowledged. WS-9025U WEATHER PROJECTION STATION POSTE METEO A PROJECTION ESTACION CON PROYECCIÓN DEL ESATDO DEL TIEMPO FCC ID: OMO-01RX (receiver), OMO-01TX (sensor) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. [. . . ] For areas that do not recognize DST changes (Arizona and parts of Indiana) turn the DST "OFF". Confirm with the SET key and enter the Time Reception ON/OFF setting. In area where reception of the WWVB time is not possible, the WWVB time reception function can be turn OFF. Note: If the Time Reception function is turned OFF manually, the clock will not attempt any reception of the WWVB time as long as the Time Reception OFF function is activated. The Time Reception and the "WWVB" icons will not be displayed on the LCD. 12/24-HOUR SETTING: Flashing TIME RECEPTION ON/OFF SETTING: Digits flashing The hour display can be selected to show hours in 12-hour or 24-hour settings. Use the CH/+ key to toggle between "12H" or "24H". Confirm with the SET key and enter the Manual time setting. MANUAL TIME SETTING: In case the Weather Projection Station cannot detect the WWVB-signal (for example due to disturbances, transmitting distance, etc. ), the time can be manually set. Confirm with the SET key and enter the Calendar setting. CALENDAR SETTING: Date and month (24hr time format) Month and date (12hr time format) Year 1. 5. Note: The unit will still try to receive the signal between 12:00 to 6:00 a. m. every day despite it being manually set and if the WWVB time reception function has been set ON. When it does receive the signal, it will change the manually set time into the received time. If reception has been unsuccessful, then the WWVB tower icon will not appear but reception will still be attempted the following hour. The date default of the Weather Projection Station is 1. Once the radio-controlled time signals are received, the date is automatically updated. However, if the signals are not received, the date can also be set manually. Press the SET key again to confirm and to enter the date setting mode. Confirm all calendar settings with the SET key and enter the Snooze setting. SNOOZE SETTING: Snooze time The snooze time can be set OFF to a maximum time of 30 minutes (default is 10 minutes): 1. The snooze can also be set OFF when the "OFF" digit is being displayed. Confirm with the SET key and enter the Temperature setting Note: If the snooze time has been set "OFF", the snooze function will not be activated. 1. 2. Use the CH/+ key to toggle between "°F" or "°C". Confirm with the SET key and enter the Weather forecasting icon sensitivity setting. WEATHER FORECASTING ICON SENSITIVITY SETTING: Digit flashing Icons flashing °F/°C TEMPERATURE SETTING: Digit flashing The temperature display can be selected to show temperature data in °F or °C (Default °F). For locations with rapid changes of weather conditions, the weather icons can be set to a different level for faster display of weather conditions. There are 3 levels of setting: 1, 2 and 3; level 1 is the most sensitive setting; level 3 is the slowest recording setting (default setting is "2"). Confirm with the SET key and exit the Manual settings. ALARM SETTING: SNOOZE ACTIVATION AND STOPPING THE ALARM: The snooze function can be activated when the alarm is ringing by pressing the SNOOZE key. However the snooze will only be activated when the snooze time is set other than OFF in snooze setting. [. . . ] If no reception is possible despite the observation of these factors, all system units have to be reset (see "Setting up" above). CARE AND MAINTENANCE: · · Extreme temperatures, vibration and shock should be avoided as these may cause damage to the units and give inaccurate forecasts and readings. Do not use solvents or scouring agents as they may mark the LCD and casings. · · · · Do not submerge the units in water. Immediately remove all low powered batteries to avoid leakage and damage. Return it to their original point of purchase for repair by a qualified engineer. [. . . ]