User manual LEXMARK C752

[. . . ] C752 User's Reference June 2003 www. lexmark. com Lexmark and Lexmark with diamond design are trademarks of Lexmark International, Inc. , registered in the United States and/or other countries. 740 West New Circle Road Lexington, Kentucky 40550 Table of contents Chapter 1: Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Edition notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Licensing notice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] An error message is displayed until someone replaces the toner cartridge. If an Auto Continue value is selected from the Setup Menu, the printer resumes printing after the specified timeout value. Printer stops printing, displays an error message, and sounds three quick beeps. Printer stops printing, displays an error message, and repeats three beeps every 10 seconds until the toner cartridge is replaced. Specifies the amount of time the printer waits for additional data before it cancels the job. Staple Alarm Single* Continuous Toner Alarm To specify how the printer responds when it is low on toner. Off Single* Continuous Wait Timeout To specify the amount of time (in seconds) the printer waits to receive additional bytes of data from the computer. This menu item has no effect on PCL emulation print jobs. Disabled 15. . . 65535 (40*) 71 Supplies Menu The Supplies Menu provides information about printer supplies that require attention. It is only available when a supply is low or needs replacement. Menu Item Purpose To view the status of the color print cartridges. Note: Once the toner waste container reaches Full, the printer will print up to 15 more pages from the buffer and then stop until the container is replaced. Values Low Change Cartridge Near Exhausted Near Full The toner waste container is nearly full. <color> Toner Oiler Waste Bottle USB Menu Use the USB Menu to change printer settings affecting a Universal Serial Bus (USB) port (USB Option <x>). Note: Values marked by an asterisk (*) are the factory default settings. Menu Item Purpose To temporarily store jobs on the printer hard disk before printing. Note: Changing the Job Buffering menu item automatically resets the printer. Buffers print jobs only if the printer is busy processing data from another input port. Printer processes raw binary PostScript print jobs from computers using the Macintosh operating system. On Auto* Printer filters PostScript print jobs using standard protocol. Printer processes print jobs from computers using either Windows or Macintosh operating systems. Job Buffering MAC Binary PS To configure the printer to process Macintosh binary PostScript print jobs. Off 72 Menu Item Purpose To specify whether the printer performs the special processing required for bidirectional communication, following the conventions defined in the Network Printing Alliance (NPA) Protocol. Note: Changing this menu item automatically resets the printer. Values Off Printer performs NPA processing. Printer examines the data to determine the format and then processes it appropriately. Printer examines the data on the USB interface and selects PCL emulation if the data indicates that is the required printer language. The printer uses PostScript emulation to process the job if PS SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PS SmartSwitch is Off. Printer examines data on the USB interface and selects PostScript emulation if the data indicates that is the required printer language. The printer uses PCL emulation to process the job if PCL SmartSwitch is On, or uses the default printer language specified in the Setup Menu if PCL SmartSwitch is Off. Any jobs already buffered on the disk are printed before normal processing of incoming jobs resumes. [. . . ] The accuracy of the estimates may be affected by how full the print cartridges are, environmental conditions, the media type, the software application, software settings, the driver, driver settings, and the content of the page. Lexmark makes no claim as to the accuracy of the estimated percents. 152 Configuring printer alerts You can configure the printer several ways to let you know when it requires attention. Using the Setup Menu Menu item Alarm Control Function Lets you establish whether the printer sounds an alarm when it requires operator intervention. Value Off Single Continuous Toner Alarm Lets you choose how the printer responds when toner is low. Off Single Continuous Result The alarm does not sound, but printing stops until the interventions are cleared. * The printer stops printing, displays a message, and activates the selected alarm type. [. . . ]