User manual LEXMARK P250

[. . . ] P200 Series User's Guide Safety information Use only the power supply and power supply cord provided with this product or the manufacturer's authorized replacement power supply and power supply cord. Connect the power supply cord to an electrical outlet that is near the product and easily accessible. Refer service or repairs, other than those described in the user documentation, to a professional service person. This product is designed, tested, and approved to meet strict global safety standards with the use of specific manufacturer's components. [. . . ] If print quality has not improved, continue to step 3. 3 Remove and reinsert the print cartridge. For more information, see "Removing a used print cartridge" on page 17 and "Installing the print cartridge" on page 17. If print quality has not improved, continue to step 4. 4 Wipe the print cartridge nozzles and contacts. For more information, see "Wiping the print cartridge nozzles and contacts" on page 20. If print quality is still not satisfactory, replace the print cartridge. For more information, see "Ordering supplies" on page 21. Aligning the print cartridge The printer automatically aligns the print cartridge after the cartridge is installed. You may also align the print cartridge from the computer. 1 Load photo paper. 2 Open the Solution Center. Maintaining the printer 19 3 From the Maintenance tab, click Align to fix blurry edges. 4 Click Print. If you aligned the cartridge to improve print quality, print your document again. If print quality has not improved, clean the print cartridge nozzles. Cleaning the print cartridge nozzles 1 Load photo paper. 4 Click Print. A page prints, forcing ink through the print cartridge nozzles to clean them. 5 Print the document again to verify that the print quality has improved. 6 If print quality has not improved, try cleaning the nozzles up to two more times. Wiping the print cartridge nozzles and contacts 1 Remove the print cartridge. 3 Gently hold the cloth against the print cartridge nozzles for about three seconds, and then wipe in the direction shown. 4 Using another clean section of the cloth, gently hold the cloth against the contacts for about three seconds, and then wipe in the direction shown. 5 With another clean section of the cloth, repeat step 3 and step 4. For more information, see "Cleaning the print cartridge nozzles" on page 20. Maintaining the printer 20 10 Repeat "Cleaning the print cartridge nozzles" on page 20 up to two more times. 11 If print quality is still not satisfactory, replace the print cartridge. Preserving the print cartridge · Keep a new print cartridge in its packaging until you are ready to install it. · Do not remove a cartridge from the printer except to replace, clean, or store it in an airtight container. The cartridge does not print correctly if left exposed for an extended period of time. Ordering supplies Item Lexmark color print cartridge USB cable Part number 45 1021294 Notes: · For best results, use Lexmark Perfectfinish Photo Paper or Lexmark Photo Paper. Your print cartridge is not compatible with this type of paper. Paper Lexmark Perfectfinish Photo Paper Paper size · 4 x 6 in. · 10 x 15 cm Lexmark Photo Paper Note: Availability may vary by country or region. Recycling Lexmark products To return Lexmark products to Lexmark for recycling: 1 Visit our Web site at www. lexmark. com/recycle. 2 Follow the instructions on the computer screen. Maintaining the printer 21 Troubleshooting · · · · · · "Setup troubleshooting" on page 22 "Print troubleshooting" on page 24 "Jams and misfeeds troubleshooting" on page 26 "Device troubleshooting" on page 26 "Error messages troubleshooting" on page 27 "Removing and reinstalling the software" on page 28 Setup troubleshooting Power button is not lit Make sure you have disconnected the power supply cord from the printer and then from the wall outlet. 1 Plug the cord all the way into the power supply port on the printer. 2 Plug the cord into an electrical outlet that other electrical devices have been using. 2 1 3 If the light is not on, press . Software does not install The following operating systems are supported: · Windows XP (32­bit) · Windows XP (64­bit) SOLUTION 1 1 Close all open software applications. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Reorient or relocate the receiving antenna. · Increase the separation between the equipment and receiver. · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. · Consult your point of purchase or service representative for additional suggestions. The manufacturer is not responsible for radio or television interference caused by using other than recommended cables or by unauthorized changes or modifications to this equipment. Unauthorized changes or modifications could void the user's authority to operate this equipment. [. . . ]