User manual LG LT913P-B

[. . . ] OWNER'S MANUAL Dome Camera Please read this manual carefully before operating your set and retain it for future reference. MODELS LT913 Series LT713 Series P/NO : MFL62723797 LT913PI-B. CTURALI_MFL62723797_ENG. indd 1 7/12/10 2:05 PM 2 Safety Information 1 Safety Information 1 Safety Information CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. REGULATORY INFORMATION: FCC Part 15 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. [. . . ] Tighten the screws until the ceiling mounting bracket holds the ceiling firmly. 6. Assemble the camera and ceiling mounting bracket by following step a and b. Align the locking point of the surface mounting bracket and the camera. LT913PI-B. CTURALI_MFL62723797_ENG. indd 24 7/12/10 2:06 PM Installation 25 7. Tighten the locking screw. Wall mount (optional) Install the camera by the following order. After installing the camera, you should arrange the cables using the outlet box to protect the cables. 3 Installation Red Stripe CAUTION Do not expose the connected part of the camera cable jacks in the rain or moisture. Check the red stripe on one side of the safety cable. LT913PI-B. CTURALI_MFL62723797_ENG. indd 25 7/12/10 2:06 PM 26 Installation 2. Pass the connection cable through the wall mount assembly so that they hang down. 5. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 3 Installation 3. Connect the connection cable and the safety cable to the camera body. LT913PI-B. CTURALI_MFL62723797_ENG. indd 26 7/12/10 2:06 PM Installation 27 7. Assemble the camera cover as shown below. Pendant mount (Optional) Install the camera by the following order. Connect the safety cable to the pendant mount assembly. Red Stripe 3 Installation LT913PI-B. CTURALI_MFL62723797_ENG. indd 27 7/12/10 2:06 PM 28 Installation 2. Pass the connection cable through the pendant mount assembly so that they hang down. 3. Connect the connection cable and the safety cable to the camera body. LT913PI-B. CTURALI_MFL62723797_ENG. indd 28 7/12/10 2:06 PM Installation 29 5. Attach the camera to the camera assembly bracket by following step a and b. Align the locking point of the wall mount assembly and the camera. 7. Tighten the locking screw. LT913PI-B. CTURALI_MFL62723797_ENG. indd 29 7/12/10 2:06 PM 30 Operation 4 Operation Setup Menu Overview The following table shows the list of menu items and options. You can adapt the camera to your requirements by setting up the respective items in these menus. 1st level 2nd level 3rd level FOCUS MODE FOCUS FOCUS DIST RETURN IRIS AGC WDR/BLC CAMERA SET EXPOSURE BRIGHTNESS SHUTTER SENS-UP RETURN ATW AUTO COLOR TEMP WHITE BALANCE MANUAL RED BLUE RETURN ONE PUSH INDOOR/OUTDOOR - 100 to +100 - 100 to +100 AUTO/MANUAL OFF/LOW/MIDDLE/HIGH OFF/WDR/BLC/HSBLC 0 to 100 OFF, A. FLK, 1/160, . . . , X2, AUTO AUTO X2/AUTO X3/. . . /AUTO X128/OFF Contents AUTO/MANUAL/ONE PUSH/ ZOOM TRIG LT913 Series : 50 CM, 1, 8 M, 3 M, 6 M LT713 Series : 50 CM, 1 M, 3 M, 5 M 4 Operation LT913PI-B. CTURALI_MFL62723797_ENG. indd 30 7/12/10 2:06 PM Operation 31 D/N LEVEL AUTO DAY/NIGHT DAY NIGHT OFF 3D-DNR LOW MIDDLE HIGH COLOR SHARPNESS RETURN NAME SPEED DWELL TIME IRIS WDR/BLC/HSBLC ON OFF 0 to 68 COLOR DWELL TIME RETURN LOW/MIDDLE/HIGH 5, 10, 15, 30, 60 SEC -20 to 20 OFF/ON 1 to 127 1 to 255 AUTO, 20, 40, 60, 80, 100 % OFF/ LOW WDR/ MID. HSBLC/ HIGH HSBLC X512, . . . , x2, AUTO, OFF, A. FLK, 1/160, . . . , 1/90 000 4 Operation SET PRESET PAN/TILT SET SHUTTER PRESET SET POSITION SAVE RETURN GOTO PRESET PRESET TOUR CLEAR PRESET CLEAR ALL FREEZE RETURN ON/OFF 0 to 127 0 to 127 LT913PI-B. CTURALI_MFL62723797_ENG. indd 31 7/12/10 2:06 PM 32 Operation SET GROUP GROUP TOUR RUN CLEAR RETURN RECORD PATTERN RUN RETURN SET AUTO PAN AUTO PAN RUN CLEAR RETURN MASK NUMBER SET MASK MASK STATE PRIVACY MASK MASK COLOR WIDTH HEIGHT RETURN PROPORTIONAL PT COMPASS 1 to 9 1 to 9 1 to 9 1 to 4 1 to 4 1 to 8 1 to 8 ON/OFF GRAY, WHITE, BLACK 2 to 320 3 to 240 ON/OFF SET/ON/OFF SET GO DWELL TIME(0 to 100) RETURN OFF RETURN TIME (1 MIN to 100 MIN) 4 Operation HOME POSITION ON SPECIAL AUTO RETURN TILT LIMIT ON OFF ON/OFF PROTOCOL LG MULTIX/ PELCO D/ PELCO P 2 400/ 4 800/ 19 200/ 38 400/ 9 600 BPS COMMUNICATION BAUDRATE SAVE & EXIT RETURN LT913PI-B. CTURALI_MFL62723797_ENG. indd 32 7/12/10 2:06 PM Operation 33 RETURN USER TITLE ZOOM MAG OSD SET FUNCTION DOME ID RETURN LANGUAGE The option depends on the model. NORMAL ALARM IN1 to ALARM IN4 ALARM SET ON ALARM IN1 to ALARM IN4 DWELL TIME RETURN OFF ALARM OUT1 to ALARM OUT2 ALARM OUT1 to ALARM OUT2 ON OFF INFORMATION RESET INITIALIZATION FACTORY RESET RETURN RETURN DWELL TIME RETURN ALARM IN1 to ALARM IN4 3 to 255 OPEN/CLOSE PRESET 0 to 127 3 to 255 ON/OFF ON/OFF ON/OFF ON/OFF 4 Operation LT913PI-B. CTURALI_MFL62723797_ENG. indd 33 7/12/10 2:06 PM 34 Operation Please Enter Camera ID Target CAM ID : _ 2. Enter the connected camera ID to control the camera connected to the LKD1000 controller directly and then press ENTER. [. . . ] The camera will move to the home position. NOTE If you set [AUTO RETURN] to [ON], the [HOME POSITION] option is set to [OFF] automatically and you can not use it. Tilt limit You can specify the tilt range. If you set this function, the camera is able to tilt from 15º to 165º. If you do not want to use this function, set it to [OFF]. Communication This setting is required to establish a connection between the system controller and the camera. · · Protocol: This item lets you set a protocol for RS-485 communication. [. . . ]