User manual LIFESCAN ONETOUCH ULTRA 2 TEST GUIDE

[. . . ] It contains the same information in a shorter format, and will help you get to know your blood glucose monitoring system. A free videotape is also available by calling the LifeScan Customer Services Department. Blood glucose monitoring plays an important role in controlling your diabetes. The results you get with the ONE TOUCH II System can help you and your healthcare professional monitor and adjust your treatment plan (diet, exercise, and medication) to help you gain better control of your diabetes. [. . . ] Repeat the check strip test. MESSAGE not enough blood retest PROBLEM 1. The blood or control solution sample was too small or smeared. WHAT TO DO 1. Repeat the test with a new test strip and a large, shiny drop of blood or control solution. Repeat the test, pushing the test strip all the way into the test strip holder. 7. 36 MESSAGE not ok PROBLEM Your meter may have an electronic problem. The check strip test result is outside the acceptable range. WHAT TO DO Call LifeScan Customer Services. MESSAGE code 7 redo A (example) PROBLEM The last check strip test result was outside the acceptable range and an acceptable repeat test was not performed. The test strip was inserted before the meter was ready. WHAT TO DO Stop and do a check strip test. A 105 Anotok redo A (example) Repeat the test. Clean the meter and the check strip if necessary. remove strip Remove the test strip. Wait for the insert strip message. 37 MESSAGE reset code PROBLEM The meter has lost some important information, including the code number. WHAT TO DO Use the C button to reset the meter code to match with the test strip vial code. Call LifeScan Customer Services. ) 38 Special Function and Memory Messages This last group of display messages has to do with the meter memory and other special features of the ONE TOUCH® II Blood Glucose Monitoring System. MESSAGE memory WHAT IT MEANS You have entered the meter's memory by pushing the M button. If you drop the meter, make sure the test strip holder is still securely in place and check the meter with the check strip before doing a blood glucose test. Avoid exposing the meter or test strips to extremes in temperature or humidity for long periods of time. The meter could be permanently damaged if water or other liquids get inside. Taking the meter apart will invalidate the meter warranty. Doing a Daily Check Look through the small hole in the test strip holder to make sure there is no lint, dirt, or blood blocking any part of the hole. If there is anything blocking the hole, or if the test area has dirt, lint, or blood on it, remove the test strip holder and clean the test area by following the instructions in the next section. Perform a check strip test by following the instructions on page 10. Cleaning the Meter The meter and test strip holder should be cleaned: 43 · At least once each week, · Whenever the test area looks dirty, and · Whenever clean test area appears on the display. Step 1: Remove Test Strip Holder from the Meter. Hold the meter and place your thumbs on the two raised dots on the test strip holder. Remove the test strip holder to expose the test area. Step 2: Clean Test Strip Holder. Wash the test strip holder with soap and water. 44 Clean the underside of the test strip holder and check the small hole for any dirt, blood, or lint. DO NOT USE: · Alcohol · Cleansers with ammonia or phenol · Windex® or other glass cleaners · Abrasive cleansers Check the clear, protective coating over the test area to make sure it is not scratched or damaged. Dry completely with a soft cloth or tissue. 45 Dry the test area with a soft, dry tissue or cloth. Hook the bottom of the test strip holder onto the square notch on the meter. Press down on the raised dots of the test strip holder until it snaps firmly into place. Rub the test area with a cotton swab or soft cloth dampened with water to remove all blood, dirt, or lint from the test area. If necessary, a mild liquid dishwashing detergent mixed with water may also be used. Be careful not to scratch the test area. S PA L OO LC D'A 46 Press forward on the base of the test strip holder to be sure it is properly in place. Replacing the Battery The ONE TOUCH ® II Meter comes with a battery already installed. [. . . ] Operating Humidity Range: 0%­90% relative humidity (noncondensing). Memory: Storage capacity-- 250 test results including check strip and control solution test results (oldest test deleted first). Data Port: Communicates with Data ManagerTM unit and other data management systems. 73 Guarantee and Warranty 30-Day Money-Back Guarantee If you are not fully satisfied with the ONE TOUCH® II System, a full refund may be obtained by calling a LifeScan Customer Services Representative at the tollfree number within 30 days of purchase. You must return the ONE TOUCH® II Meter and a copy of your receipt to receive a refund. Five-Year Warranty If, at any time during the first five years after purchase, the meter does not work for any reason (except for obvious abuse), LifeScan will replace it with a new meter or equivalent product free of charge. [. . . ]