User manual LIFT-MASTER 1145C

[. . . ] Unit 11, 230 Bayview Drive Barrie, Ontario L4N 5E9 Owner's Manual Garage Door Opener (1100 Series -- Canada) FOR RESIDENTIAL USE ONLY CAUTION!PLEASE READ THIS MANUAL CAREFULLY The MODEL NUMBER label is located on the front panel of your opener CONTENTS PAGE CONTENTS PAGE Safety Rules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Carton Inventory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Door will CLOSE if door control button is pressed and held until the door closes fully. If button is released before down travel is completed, door will reverse. Normal operation will LIGHT SWITCH TO ACTIVATE: Press Light Switch button. Opener light will turn on (or remain on if opener is still in 41/2 minute automatic cycle). WIRING INSTRUCTIONS FOR ACCESSORIES NOTE: To turn light OFF during 4-1/2 minute automatic cycle, press Light Switch button twice · to activate and then to turn off Light Switch Feature. The Protector SystemTM To white and black opener terminals Outdoor Key Switch: To red and white opener terminals INSTALL THE LIGHTS Install a 75 Watt maximum light bulb in each socket. Lights will turn ON and remain lit for 4-1/2 minutes when power is connected. If bulbs burn out prematurely due to vibration, replace with "Garage Door Opener" bulbs. For convenience, lenses may be installed after Adjustment Step 3, Page 22. 15 INSTALLATION STEP 6 Attach Manual Release Rope & Handle USE MANUAL RELEASE ROPE ONLY TO DISENGAGE TROLLEY. DO NOT USE ROPE AND HANDLE TO PULL DOOR OPEN OR CLOSED. PROCEDURE: Thread one end of rope through hole in top of red handle so 'NOTICE' reads right side up as shown. NOTE: Knot should be at least 1" from the end of the rope to prevent slipping. Thread other end of rope through hole in release arm of outer trolley. NOTE: If it is necessary to cut rope, heat seal cut end with a match or lighter to prevent fraying and/or raveling. INSTALLATION STEP 7 Connect Electric Power Opener MUST be permanently wired or plugged into a grounded 3-prong receptacle wired according to local electrical codes. DO NOT USE an extension cord. TO AVOID SERIOUS PERSONAL INJURY FROM ENTANGLEMENT, REMOVE ALL THE ROPES CONNECTED TO GARAGE DOOR BEFORE OPERATING OPENER. TO AVOID DAMAGE TO GARAGE DOOR AND OPENER, MAKE DOOR LOCKS INOPERATIVE BEFORE CONNECTING ELECTRIC POWER. USE A WOOD SCREW OR NAIL TO HOLD LOCKS IN "OPEN" /UNLOCKED) POSITION. THE INSTALLATION & THE WIRING MUST BE IN COMPLIANCE WITH LOCAL ELECTRICAL AND BUILDING CODES. OPERATION AT OTHER THAN 120V 60Hz WILL CAUSE OPENER MALFUNCTION AND DAMAGE. RIGHT WRONG PROCEDURE FOR PERMANENT WIRING (if required by local codes) DISCONNECT THE POWER AT THE FUSE BOX BEFORE PROCEEDING. Refer to illustration. Connect black (line) wire to black wire on terminal block; white (neutral) wire to white terminal wire; Green (GROUND) wire to green around screw. CAUTION: BE SURE THE UNIT IS GROUNDED ACCORDING TO LOCAL CODE. IMPORTANT NOTE: TO AVOID INSTALLATION DIFFICULTIES, DO NOT RUN OPENER NOW. 16 INSTALLATION STEP 8 Fasten Door Bracket and Plate Follow instructions which apply to your door type as illustrated below. TO PREVENT DAMAGE TO LIGHTWEIGHT AND METAL GARAGE DOORS (OR THOSE WITH GLASS PANELS), ALWAYS REINFORCE THE INSIDE OF DOOR-- BOTH VERTICALLY AND HORIZONTALLY--WITH 2X4 BOARDS OR ANGLE IRON. The horizontal brace should be at least six feet long. The best solution is to check with the garage door manufacturer for a door reinforcement kit to be used with an opener installation. :: Sectional Door Installation Procedure Position door bracket and plate assembly against door within the following limits according to your requirements (and centered on vertical guideline-- or to one toot left or right of center, if necessary): A) Top edge of bracket 2" - 4" below top edge of door. Secure bracket assembly as shown. All One-Piece Door Installation Procedure NOTE: The door bracket has left and right side fastening holes. Assemble and Install the door bracket and plate if your installation requires top and bottom fastening holes. [. . . ] Complete with: Spring washer Thrust washer Retaining ring Bearing plate Roll pins (2) Drive gear Worm gear Helical gear w/retainer Grease Drive/worm gear kit w/ grease Roll pins (2) Line cord End panel (Model 1145) End panel (Model 1160, 1150) Light socket Lens (Model 1145) Lens (Models 1160, 1150) Capacitor - 1/2HP Capacitor - 1/3HP Capacitor baracket KEY NO. 41A3150 41D3058 DESCRIPTION Terminal block w/screws Universal replacement motor /bracket assy. and RPM sensor) Cover (Specify model) Helical gear & retainer w/grease Limit switch assembly RPM sensor assembly Wire harness assy. (Model 1145) (Models 1160 and 1150) Complete with: Logic board End panel w/all labels End panel w/all labels (Model 1145) End panel w/all labels (1160 and 1150) NOT SHOWN Chassis assy. [. . . ]