User manual MAKITA 4340T

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 4340T. We hope that this MAKITA 4340T user guide will be useful to you.


MAKITA 4340T : Download the complete user guide (956 Ko)

You may also download the following manuals related to this product:

   MAKITA 4340T (1625 ko)
   MAKITA 4340T (1625 ko)
   MAKITA 4340T (1625 ko)
   MAKITA 4340T (1625 ko)
   MAKITA 4340T ANNEXE 576 (667 ko)
   MAKITA 4340T ANNEXE 164 (667 ko)

Manual abstract: user guide MAKITA 4340T

Detailed instructions for use are in the User's Guide.

[. . . ] Failure to do so may cause insufficient tightening of the blade, resulting in a serious injury. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. [. . . ] For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. The tool speed can be infinitely adjusted between 800 and 2, 800 strokes per minute by turning the adjusting dial. Higher speed is obtained when the dial is turned in the direction of number 5; lower speed is obtained when it is turned in the direction of number 1. Refer to the table below to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. CAUTION: Do not look in the light or see the source of light directly. Be careful not to scratch the lens of lamp, or it may lower the illumination. Failure to do so may cause blade breakage, resulting in a serious injury. Then rest the tool base flat on the workpiece and gently move the tool forward along the previously marked cutting line. CAUTION: Always be sure that the tool is switched off and unplugged before tilting the tool base. With the tool base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). Move the base so that the bolt is positioned in the center of the bevel slot in the base. CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing accessories. When repeatedly cutting widths of 160 mm or less, use of the rip fence will assure fast, clean, straight cuts. To install, insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing down. When cutting circles or arcs of 170 mm or less in radius, install the rip fence as follows. Insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing up. Insert the circular guide pin through either of the two holes on the fence guide. now slide the rip fence to the desired cutting radius , and tighten the bolt to secure it in place. Loosen the bolt on the back of the tool base with the hex wrench, then move the tool base all the way back. [. . . ] When you use the cover plate, install the anti-splintering device onto the cover plate. CAUTION: The anti-splintering device cannot be used when making bevel cuts. CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service Center. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 4340T




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 4340T will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.