User manual MAKITA 4341T

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 4341T. We hope that this MAKITA 4341T user guide will be useful to you.


MAKITA 4341T : Download the complete user guide (912 Ko)

You may also download the following manuals related to this product:

   MAKITA 4341T (1575 ko)
   MAKITA 4341T (1575 ko)
   MAKITA 4341T (1575 ko)
   MAKITA 4341T (1575 ko)
   MAKITA 4341T ANNEXE 69 (671 ko)
   MAKITA 4341T ANNEXE 759 (671 ko)

Manual abstract: user guide MAKITA 4341T

Detailed instructions for use are in the User's Guide.

[. . . ] Failure to do so may cause insufficient tightening of the blade, resulting in a serious injury. Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. [. . . ] Refer to the table below to select the proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. CAUTION: Do not look in the light or see the source of light directly. Be careful not to scratch the lens of lamp, or it may lower the illumination. Failure to do so may cause blade breakage, resulting in a serious injury. Then rest the tool base flat on the workpiece and gently move the tool forward along the previously marked cutting line. CAUTION: The speed adjusting dial can be turned only as far as 5 and back to 1. Do not force it past 5 or 1, or the speed adjusting function may no longer work. Always be sure that the tool is switched off and unplugged before tilting the tool base. With the tool base tilted, you can make bevel cuts at any angle between 0° and 45° (left or right). Move the base so that the bolt is positioned in the center of the bevel slot in the base. CAUTION: Always be sure that the tool is switched off and unplugged before installing or removing accessories. When repeatedly cutting widths of 160 mm or less, use of the rip fence will assure fast, clean, straight cuts. To install, insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing down. When cutting circles or arcs of 170 mm or less in radius, install the rip fence as follows. Insert the rip fence into the rectangular hole on the side of the tool base with the fence guide facing up. Insert the circular guide pin through either of the two holes on the fence guide. now slide the rip fence to the desired cutting radius , and tighten the bolt to secure it in place. Loosen the bolt on the back of the tool base with the hex wrench, then move the tool base all the way back. [. . . ] When you use the cover plate, install the anti-splintering device onto the cover plate. CAUTION: The anti-splintering device cannot be used when making bevel cuts. CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by a Makita Authorized Service Center. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 4341T




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 4341T will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.