User manual MAKITA 6347D

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 6347D. We hope that this MAKITA 6347D user guide will be useful to you.


MAKITA 6347D : Download the complete user guide (534 Ko)

You may also download the following manuals related to this product:

   MAKITA 6347D (550 ko)
   MAKITA 6347D (363 ko)
   MAKITA 6347D (550 ko)
   MAKITA 6347D (550 ko)
   MAKITA 6347D (1074 ko)
   MAKITA 6347D (1074 ko)
   MAKITA 6347D (1074 ko)
   MAKITA 6347D ANNEXE 17 (475 ko)
   MAKITA 6347D ANNEXE 59 (475 ko)
   MAKITA 6347D ANNEXE 55 (475 ko)
   MAKITA 6347D ANNEXE 887 (152 ko)
   MAKITA 6347D ANNEXE 572 (203 ko)
   MAKITA 6347D ANNEXE 976 (475 ko)
   MAKITA 6347D ANNEXE 157 (475 ko)
   MAKITA 6347D ANNEXE 939 (1074 ko)
   MAKITA 6347D ANNEXE 991 (1074 ko)
   MAKITA 6347D ANNEXE 742 (1074 ko)
   MAKITA 6347D ANNEXE 889 (1074 ko)
   MAKITA 6347D ANNEXE 874 (1074 ko)
   MAKITA 6347D ANNEXE 318 (475 ko)
   MAKITA 6347D ANNEXE 772 (1074 ko)
   MAKITA 6347D ANNEXE 141 (1074 ko)
   MAKITA 6347D ANNEXE 966 (1074 ko)
   MAKITA 6347D ANNEXE 902 (475 ko)
   MAKITA 6347D ANNEXE 691 (475 ko)
   MAKITA 6347D ANNEXE 913 (152 ko)
   MAKITA 6347D ANNEXE 345 (203 ko)
   MAKITA 6347D ANNEXE 658 (475 ko)
   MAKITA 6347D ANNEXE 322 (1074 ko)

Manual abstract: user guide MAKITA 6347D

Detailed instructions for use are in the User's Guide.

[. . . ] Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. Always stop tool operation and charge the battery cartridge when you notice less tool power. Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months. [. . . ] for screwing , slide the action mode change lever to the right ( U symbol) until it is locked. If it is hard to turn the lever, first turn the chuck slightly in either direction and then turn the lever again. cAUTION: · Always slide the action mode change lever all the way to your desired mode position. If you operate the tool with the lever positioned halfway between the mode symbols, the tool may be damaged. ⷠDo not use the action mode change lever while the tool is running. Always switch off the tool before insertion or removal of the battery cartridge. ⷠTo remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. ⷠTo insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. ⷠDo not use force when inserting the battery cartridge. If the cartridge does not slide in easily, it is not being inserted correctly. The fastening torque can be adjusted in 16 steps by turning the adjusting ring so that its graduations are aligned with the pointer on the tool body. fIrst , slide the action mode change lever to the position of U symbol. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the marking is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. cAUTION: · The adjusting ring does not lock when the pointer is positioned only halfway between the graduations. CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. Drilling in metal To prevent the bit from slipping when starting a hole, make an indentation with a center-punch and hammer at the point to be drilled. In fact, this excessive pressure will only serve to damage the tip of your bit, decrease the tool performance and shorten the service life of the tool. [. . . ] EC-DECLARATION OF CONFORMITY Model; 6207D, 6217D, 6317D, 6337D, 6347D We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents, EN60745, EN55014 in accordance with Council Directives, 2004/108/EC and 98/37/EC. For European countries only For Model 6207D Noise The typical A-weighted noise level determined according to EN60745-2-1: Sound pressure level (LpA): 70 dB (A) or less The noise level under working may exceed 85 dB (A). Vaibration The vibration total value (tri-axial vector sum) determined according to EN60745-2-1: Work mode: Driling into metal Vibration emission (ah, D): 2. For European countries only For Model 6217D, 6317D Noise The typical A-weighted noise level determined according to EN60745-2-1: Sound pressure level (LpA): 72 dB (A) Uncertainty (K): 3 dB (A) The noise level under working may exceed 85 dB (A). [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 6347D




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 6347D will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.