User manual MAKITA 6820V

[. . . ] In observance of European Directive 2002/96/EC on waste electrical and electronic equipment and its implementation in accordance with national law, electric equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. For European countries only Noise and Vibration ENG003-2-V2 EC-DECLARATION OF CONFORMITY ENH101-5 The typical A-weighted sound pressure level is 81 dB (A). ­ The typical weighted root mean square acceleration value is not more than 2. 5 m/s2. These values have been obtained according to EN60745. We declare under our sole responsibility that this product is in compliance with the following standards of standardized documents, EN60745, EN55014, EN61000 in accordance with Council Directives, 89/336/EEC and 98/37/EC. Yasuhiko Kanzaki CE 2005 Director MAKITA INTERNATIONAL EUROPE LTD. Michigan Drive, Tongwell, Milton Keynes, Bucks MK15 8JD, ENGLAND Responsible manufacturer: Makita Corporation Anjo Aichi Japan 2 1 2 3 4 5 6 7 3 ENGLISH Explanation of general view 1 2 3 Locator Stopper Magnetic bit holder 4 5 6 Bit Locking sleeve Speed control screw 7 8 9 Switch trigger Lock button Reversing switch lever GENERAL SAFETY RULES WARNING!Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. [. . . ] This enables better control of the power tool in unexpected situations. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The correct power tool will do the job better and safer at the rate for which it was designed. Any power tool that cannot be controlled with the switch is dangerous and must be repaired. Disconnect the plug from the power source and/ or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation. Have your power tool serviced by a qualified repair person using only identical replacement parts. Follow instruction for lubricating and changing accessories. 4 25. Keep handles dry, clean and free from oil and grease. Switch action (Fig. 5) CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. tool speed is increased by increasing pressure on the trigger. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. A speed control screw is provided so that maximum tool speed can be limited (variable). Turn the speed control screw clockwise for higher speed, and counterclockwise for lower speed. NOTE: Even with the switch on and motor running, the bit will not rotate until you fit the point of the bit in the screw head and apply forward pressure to engage the clutch. SPECIFIC SAFETY RULES GEB017-1 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to screwdriver safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. [. . . ] NOTE: Make sure that the bit is inserted straight in the screw head, or the screw and/or bit may be damaged. Depth adjustment (Fig. 2, 3 & 4) Push the locking sleeve in toward the motor and turn slightly clockwise to lock it. Initially, adjust the locator so that the tip of the locator is flush with the base of the screw head. Turn the locking sleeve slightly so that the protrusions on the locking sleeve engage in the notches in the locator. [. . . ]