User manual MAKITA 9561CH

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 9561CH. We hope that this MAKITA 9561CH user guide will be useful to you.


MAKITA 9561CH : Download the complete user guide (614 Ko)

You may also download the following manuals related to this product:

   MAKITA 9561CH (1260 ko)
   MAKITA 9561CH (1260 ko)
   MAKITA 9561CH (1260 ko)
   MAKITA 9561CH (1260 ko)

Manual abstract: user guide MAKITA 9561CH

Detailed instructions for use are in the User's Guide.

[. . . ] Make sure the wheel is not contacting the workpiece before the switch is turned on. Hold the tool so that sparks fly away from you and other persons or flammable materials. Pay attention that the wheel continues to rotate after the tool is switched off. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. [. . . ] The tools equipped with electronic function are easy to operate because of the following features. Electronic constant speed control Possible to get fine finish, because the rotating speed is kept constantly even under the loaded condition. Overload protector When the tool would be employed over the admissible load, it will stop automatically to protect the motor and wheel. When the load will come to the admissible level again, the tool can be started automatically. Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when the rear of the slide switch is depressed. to start the tool , slide the slide switch toward the "I (ON)" position. For continuous operation, press the front of the slide switch to lock it. Before plugging in the tool, always check to see that the slide switch actuates properly and returns to the "OFF" position when released. Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. Always be sure that the side grip is installed securely before operation. 5 & 6) CAUTION: · The wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard around 180 degrees clockwise (for 9563C, 9563CV) or counterclockwise (for 9561CH, 9561CVH, 9562CH, 9562CVH, 9564C, 9564CV, 9565C, 9565CV). 7 & 8) Pull the lever in the direction of the arrow after loosening the screw. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Fasten it with the screw after pulling lever in the direction of the arrow for the working purpose. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury. cAUTION: · After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down. Fit the wheel/ disc on the inner flange and screw the lock nut onto the spindle. 9) To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. ALWAYS hold the tool firmly with one hand on housing and the other on the side handle. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. [. . . ] The use of any other accessories or attachments might present a risk of injury to persons. If you need any assistance for more details regarding these accessories, ask your local Makita Service Center. Wheel guard (Wheel cover) Inner flange Depressed center wheels Lock nut (For depressed center wheel) Rubber pad Abrasive discs Lock nut (For abrasive disc) Lock nut wrench Wire cup brush Wire bevel brush 85 Side grip Diamond wheel Dust collecting wheel guard Draai daarna de beschermkap 180 graden rechtsom (voor model 9563C, 9563CV) of linksom (voor model 9561CH, 9561CVH, 9562CH, 9562CVH, 9564C, 9564CV, 9565C, 9565CV). Ratten för inställning av varvtalet kan endast vridas till 5, och sedan tillbaka till 1. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 9561CH




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 9561CH will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.