User manual MAKITA 9561CVR

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 9561CVR. We hope that this MAKITA 9561CVR user guide will be useful to you.


MAKITA 9561CVR : Download the complete user guide (1315 Ko)

Manual abstract: user guide MAKITA 9561CVR

Detailed instructions for use are in the User's Guide.

[. . . ] Shaft lock Slide switch Indication lamp (speed adjusting dial) Indication lamp Speed adjusting dial Wheel guard Bearing box 8. Rated speed (n) / No load speed (no) Overall length Net weight Safety class Due to our continuing program of research and development, the specifications herein are subject to change without notice. â· Note: Specifications may differ from country to country. END202-4 Symbols The following show the symbols used for the equipment. [. . . ] Wheel intended for larger power tool is not suitable for the higher speed of a smaller tool and may burst. overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage. B) Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you. C) When wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. The wheel may bind, walk up or kickback if the power tool is restarted in the workpiece. E) Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel. F) Use extra caution when making a "pocket cut" into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback. Safety Warnings Specific for Sanding Operations: a) Do not use excessively oversized sanding disc paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback. Safety Warnings Specific for Wire Brushing Operations: a) Be aware that wire bristles are thrown by the brush even during ordinary operation. B) If the use of a guard is recommended for wire brushing, do not allow interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. When using depressed center grinding wheels, be sure to use only fiberglass-reinforced wheels. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Make sure the wheel is not contacting the workpiece before the switch is turned on. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel. Hold the tool so that sparks fly away from you and other persons or flammable materials. Do not touch the workpiece immediately after operation; it may be extremely hot and could burn your skin. [. . . ] Make sure that the arrow on the tool should point in the same direction as the arrow on the diamond wheel. Fit the diamond wheel on over the inner flange and screw the lock nut onto the spindle. Notice that flat side of the lock nut should face the diamond wheel in case the diamond wheel is used. Forcing and exerting excessive pressure or allowing the wheel to bend, pinch or twist in the cut can cause overheating of the motor and dangerous kickback of the tool. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 9561CVR




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 9561CVR will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.