User manual MAKITA AF505

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA AF505. We hope that this MAKITA AF505 user guide will be useful to you.


MAKITA AF505 : Download the complete user guide (711 Ko)

You may also download the following manuals related to this product:

   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (814 ko)
   MAKITA AF505 (202 ko)
   MAKITA AF505 ANNEXE 400 (814 ko)
   MAKITA AF505 ANNEXE 181 (814 ko)
   MAKITA AF505 PARTS (712 ko)
   MAKITA AF505 PART LISTS (744 ko)
   MAKITA AF505 PARTS LIST (712 ko)
   MAKITA AF505 ANNEXE 598 (814 ko)

Manual abstract: user guide MAKITA AF505

Detailed instructions for use are in the User's Guide.

[. . . ] Always wear safety glasses to protect your eyes from dust or nail injury. WARNING: It is an employer's responsibility to enforce the use of safety eye protection equipment by the tool operators and by other persons in the immediate working area. Wear hearing protection to protect your ears against exhaust noise and head protection. Do not operate when under the influence of alcohol, drugs or the like. [. . . ] Use an air hose as large and as short as possible to assure continuous, efficient nailing operation. 7 kgf/cm2G (150 PSIG) or 150 percent of the maximum pressure produced in the system whichever is higher. CAUTION: Low air output of the compressor, or a long or smaller diameter air hose in relation to the nailing frequency may cause a decrease in the driving capability of the tool. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 60 times per minute at a compression of 7. 0 kgf/cm2G (100 PSIG) , a compressor with an air output over 2 CFM ( ft3/minute) is required. Pressure regulators must be used to limit air pressure to the rated pressure of the tool where air supply pressure exceeds the tool's rated pressure. Failure to do so may result in serious injury to tool operator or persons in the vicinity. Adjust the oiler so that one drop of oil will be provided for every 50 nails. When an air set is not used, oil the tool with pneumatic tool oil by placing 2 (two) or 3 (three) drops into the air fitting. For proper lubrication, the tool must be fired a couple of times after pneumatic tool oil is introduced. CAUTION: Always disconnect the hose before carrying out any work on the tool. Load the same kind, size and uniform length of nails when loading nails in the magazine. The depth of nailing is the deepest when the adjuster is turned fully in the A direction shown in the figure. It will become shallower as the adjuster is turned in the B direction. If nails cannot be driven deep enough even when the adjuster is turned fully in the A direction, increase the air pressure. If nails are driven too deep even when the adjuster is turned fully in the B direction, decrease the air pressure. Generally speaking, the tool service life will be longer when the tool is used with lower air pressure and the adjuster set to a lower depth of nail driving. [. . . ] Also, route the hose away from obstacles which it may become dangerously caught on during operation. Hoses must also be directed away from sharp edges and areas which may lead to damage or abrasion to the hose. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Use protección para los oídos para protegerlos contra el ruido del escape, así como también debe usarse protección para la cabeza. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA AF505




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA AF505 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.