User manual MAKITA AN711H

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA AN711H. We hope that this MAKITA AN711H user guide will be useful to you.


MAKITA AN711H : Download the complete user guide (1389 Ko)

You may also download the following manuals related to this product:

   MAKITA AN711H ANNEXE 18 (880 ko)
   MAKITA AN711H ANNEXE 974 (880 ko)
   MAKITA AN711H ANNEXE 425 (880 ko)
   MAKITA AN711H ANNEXE 900 (880 ko)
   MAKITA AN711H ANNEXE 624 (880 ko)
   MAKITA AN711H ANNEXE 670 (880 ko)
   MAKITA AN711H ANNEXE 786 (880 ko)
   MAKITA AN711H ANNEXE 311 (880 ko)
   MAKITA AN711H ANNEXE 455 (890 ko)
   MAKITA AN711H ANNEXE 946 (890 ko)
   MAKITA AN711H ANNEXE 641 (890 ko)
   MAKITA AN711H ANNEXE 847 (890 ko)
   MAKITA AN711H ANNEXE 361 (890 ko)
   MAKITA AN711H ANNEXE 276 (890 ko)
   MAKITA AN711H ANNEXE 973 (890 ko)
   MAKITA AN711H ANNEXE 981 (890 ko)
   MAKITA AN711H ANNEXE 93 (880 ko)
   MAKITA AN711H ANNEXE 797 (890 ko)

Manual abstract: user guide MAKITA AN711H

Detailed instructions for use are in the User's Guide.

[. . . ] Do not operate when under the influence of alcohol, drugs or the like. Do not point the tool toward yourself or anyone whether it contains fasteners or not. Do not activate the tool unless the tool is placed firmly against the workpiece. Do not load the tool with fasteners when any one of the operating controls is activated. [. . . ] Never connect tool to compressed air line where the maximum allowable pressure of tool cannot be exceeded by 10%. Make sure that the pressure supplied by the compressed air system does not exceed the maximum allowable pressure of the fastener driving tool. Set the air pressure initially to the lower value of the recommended allowable pressure. Do not attempt to keep the trigger or contact element depressed with tape or wire. Nails may be driven accidentally if the safety mechanism is not working correctly. select a compressor that has ample pressure and air output to assure cost-efficient operation. The graph shows the relation between nailing frequency, applicable pressure and compressor air output. Thus, for example, if nailing takes place at a rate of approximately 40 times per minute at a compression of 1. Pressure regulators must be used to limit air pressure to the rated pressure of the tool where air supply pressure exceeds the tool's rated pressure. Failure to do so may result in serious injury to tool operator or persons in the vicinity. When changing the installation position, remove the screw with a screwdriver. Install the hook on another side for installation and then secure it with the screw. Always disconnect the hose before installing or removing the nose adapter. If you like to protect the surface of workpiece, attach the nose adapter of contact element. When nailing workpieces with easily-marred surfaces, use the nose adapter. To attach the nose adapter to the contact element, press it onto the contact element until the protrusion in three places inside the nose adapter fit in three holes in the contact element. Use an air hose as large and as short as possible to assure continuous, efficient nailing operation. cAUTION: · Low air output of the compressor, or a long or smaller diameter air hose in relation to the nailing frequency may cause a decrease in the driving capability of the tool. Make sure that the coil support plate is set to the correct step for used nails. 9) Lift and turn the coil support plate so that the arrow with nail size indicated on the coil support plate will point to the corresponding graduation increment marked on the magazine. If the tool is operated with the coil support plate set to the wrong step, poor nail feed or malfunction of the tool may result. Place the first nail in the feeder and the second nail in the feed claw. [. . . ] We Makita Corporation as the responsible manufacturer declare that the following Makita machine(s): Designation of Machine: Construction Nailer Model No. / Type: AN711H are of series production and Conforms to the following European Directives: 98/37/EC until 28th December 2009 and then with 2006/42/EC from 29th December 2009 And are manufactured in accordance with the following standards or standardised documents: EN792 The technical documentation is kept by our authorized representative in Europe who is: Makita International Europe Ltd. These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA AN711H




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA AN711H will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.